Search results
2326
[Page extract]
ISO 8009
ISO 8009:2004 specifies the minimum requirements and test methods to be used for reusable diaphragms made from natural rubber and silicone rubber. These diaphragms are intended for contraceptive use.
2327
[Page extract]
ISO 1966
Describes the design requirements and tests for the crimping of insulated and non-insulated terminations to general purpose cables, with conductors of copper, copper alloy, aluminium or aluminium alloy, in locations in which the stabilized conductor tem
2328
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2329
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2330
Event
Medical Device Testing: Needle sharpness and syringe actuation testing (with 21 CFR Part 11 compliance)
Hypodermic needles are tested to determine their efficacy in piercing elastomer closures on vials and how their design influences the ease of insertion into the patient's skin, influencing pain and skin trauma.
The smooth and consistent operat
2331
Case study
ความต้านทานแรงดึงของผ้าบอลลูนลมร้อนและการทดสอบความต้านทานการฉีกขาด
ความต้องการ Ultra Magic เป็นผู้ผลิตบอลลูนลมร้อนรายใหญ่อันดับสองของโลก ด้วยเหตุผลด้านความปลอดภัยที่ชัดเจนวัสดุที่ใช้ต้องเป็นไปตามมาตรฐานที่เข้มงวดที่ใช้กับอุตสาหกรรมการบิน
2332
Case study
การทดสอบขั้วสายไฟ
ความต้องการ Cyprium Motorsports ซึ่งตั้งอยู่ใน Diss สหราชอาณาจักรออกแบบและผลิตระบบชุดสายไฟสำหรับรถสปอร์ตเช่น Formula 1, Le Mans Prototype, Grand Touring และรถแรลลี่ Cyprium จำเป็นต้องมีระบบทดสอบแรงเพื่อดำเนินการตรวจสอบขั้วสายไฟอย่างรวดเร็วและแม
2333
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
2334
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
2335
Case study
การทดสอบความตึงของฟิล์มพลาสติก
ความต้องการ ลูกค้าใช้ฟิล์มพลาสติกสองชั้นสำหรับฟิล์มบรรจุภัณฑ์สำหรับบรรจุอาหารสัตว์เลี้ยงและขนม พวกเขากำลังมองหาระบบที่ประหยัดค่าใช้จ่ายและเรียบง่ายในการวัดแรงที่ต้องใช้ในการแยกฟิล์มกว้าง 50 มม.
2337
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2338
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2339
Case study
รองที่กำหนดเองสำหรับการทดสอบการยึดเกาะของเปลือก
ตัวอย่างวิศวกรรมที่กำหนดเอง ผู้ผลิตเบาะชั้นนำที่ใช้ในยานพาหนะและเครื่องบินต้องการทดสอบความแข็งแรงในการยึดเกาะของหนังที่ยึดติดกับโลหะ วิธีการนี้ใช้ตามมาตรฐาน EN 28510-1 'Adhesives - Peel test for a flexible-bonded-to-rigid test assembly
2340
Case study
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
2341
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2343
[Page extract]
BS EN ISO 13127
This standard is only to verify that panel-tested closures with minor modifications are still compliant, by applying mechanical tests as more economical than further full panel tests with children and with adults.
2344
[Page extract]
Key standards for equibiaxial flexure testing
Internationally recognised standards ensure accuracy, repeatability, and comparability of results. Common references include:
2345
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation
2346
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.
2347
[Page extract]
BS EN ISO 10066
BS EN ISO 10066 is a test method for determining creep in tension of flexible cellular polymeric materials.
2348
Case study
Custom bottle cap mandrels
Customised engineering example
Plastic caps applied to bottles may be thin-walled and flexible, so that they become distorted when gripped by an operator during torque testing.
2349
[Page extract]
ASTM D937-97
1.1 This test method covers measuring with a penetrometer the penetration of petrolatum as an empirical measure of consistency.