Search results
2301
[Page extract]
ISO 4587
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
2302
[Page extract]
ASTM D6049-03
This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular wei
2303
[Page extract]
ISO 11607-1
Specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.
2304
[Page extract]
แท่นทดสอบแบบใช้เครื่องยนต์
การทดสอบแรงซ้ำ กำลังมองหาเครื่องทดสอบแรงดึงหรือแรงอัดแบบใช้เครื่องยนต์เพื่อปรับปรุงความแม่นยำและความแม่นยำในการวัดซ้ำเมื่อเทียบกับเครื่องวัดแรงกดแบบแมนนวล?
2305
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2306
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
2307
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
2308
[Page extract]
ISO 9856
ISO 9856 specifies a method for determining the elastic and permanent elongation of a conveyor belt and the calculation of the elastic modulus.
2309
Case study
Peel testing Ostomy bags
Requirement
Salts Healthcare, a leading manufacturer and supplier of health care products required a low capacity system for testing the integrity of their hydrocolloid products.
2310
[Page extract]
ASTM D3826
ASTM D3826 is a tensile test method, which covers a degradation-end point, or a brittle point) for degradable polyethylene/polypropylene films and sheeting less than 1.0 mm thick.
2311
[Page extract]
BS EN 12814-7
BS EN 12814-7 is a tensile test method with waisted test specimens for testing welded joints of thermoplastics semi-finished products.
2312
Event
Essentials of Cork Pull & Cork Elasticity Testing
Cork stoppers are extremely successful wine bottle closures that have been in use from ancient times.
2313
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2314
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2315
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2316
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2317
[Page extract]
FINAT FTM2
This test method differs from FTM 1 in that it can allow the end user to compare the repositionability of different laminates.
2318
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
2319
Case study
ความต้านทานแรงดึงของผ้าบอลลูนลมร้อนและการทดสอบความต้านทานการฉีกขาด
ความต้องการ Ultra Magic เป็นผู้ผลิตบอลลูนลมร้อนรายใหญ่อันดับสองของโลก ด้วยเหตุผลด้านความปลอดภัยที่ชัดเจนวัสดุที่ใช้ต้องเป็นไปตามมาตรฐานที่เข้มงวดที่ใช้กับอุตสาหกรรมการบิน
2320
Case study
การทดสอบขั้วสายไฟ
ความต้องการ Cyprium Motorsports ซึ่งตั้งอยู่ใน Diss สหราชอาณาจักรออกแบบและผลิตระบบชุดสายไฟสำหรับรถสปอร์ตเช่น Formula 1, Le Mans Prototype, Grand Touring และรถแรลลี่ Cyprium จำเป็นต้องมีระบบทดสอบแรงเพื่อดำเนินการตรวจสอบขั้วสายไฟอย่างรวดเร็วและแม
2321
[Page extract]
BS EN ISO 13002
Carbon fibres, Designations, Filament yarns, Filament (textile fibre), Textile fibres, Filaments, Reinforcing materials, Polymers, Plastics, Reinforced materials, Composite materials, Data blocks, Tensile strength, Modulus of elasticity, Linear density<
2322
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
2323
[Page extract]
ASTM D7233-08
This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent.
2324
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
2325
Case study
การทดสอบความตึงของฟิล์มพลาสติก
ความต้องการ ลูกค้าใช้ฟิล์มพลาสติกสองชั้นสำหรับฟิล์มบรรจุภัณฑ์สำหรับบรรจุอาหารสัตว์เลี้ยงและขนม พวกเขากำลังมองหาระบบที่ประหยัดค่าใช้จ่ายและเรียบง่ายในการวัดแรงที่ต้องใช้ในการแยกฟิล์มกว้าง 50 มม.