Search results
1376
[Page extract]
Why Mecmesin for puncture resistance testing
Mecmesin designs and manufactures precision puncture resistance testing systems to meet the requirements of ASTM and ISO standards.
1377
[Page extract]
ASTM D4501-01
This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
1378
[Page extract]
Introduction to insertion and withdrawal testing
Insertion and withdrawal testing is a critical method for evaluating the performance, durability, and reliability of components that require secure and repeatable connections.
1379
[Page extract]
*corp 01M-01-216
To determine the maximum force required to rupture (break) a woven fabric – Rugby only
1380
Product
Testador de tração motorizado
Alluris FMT-W40
PSV21018
O FMT-W40 é um testador de tração de terminal de fio motorizado. Ele está disponível em 2 modelos com capacidade de resistência à tração de até 500N (110 lbf) ou 1000N (220 lbf). É robusto, compacto e ocupa pouco espaço na bancada. Projetado…
1381
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
1382
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1383
[Page extract]
BS ISO 11193-1
ISO 11193-1:2008 specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves intended for use in medical examinations and diagnostic or therapeutic procedures to protect the patient and the user from cross-contamination.
1384
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
1385
[Page extract]
FAQs about compressive strength testing
How is compressive strength different from tensile strength?
1386
[Page extract]
Measurement and testing methods
Techniques for measuring tangent modulus
Tangent modulus is measured during tensile or compression testing, w
1387
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1388
[Page extract]
What is lap shear testing under compression?
Lap shear testing under compressive load is a mechanical test used to determine the strength of
1389
[Page extract]
Introduction to Delft tear testing
The Delft tear test is a specialised method for determining the tear strength of vulcanised rubber, thermoplastic elastomers and similar flexible materials.
1390
[Page extract]
Coefficient of friction (COF) explained
Understanding the COF formula
The coefficient of friction (μ) is a dimensionless value calculated as:
1391
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1392
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1393
[Page extract]
BS EN 62275
This International Standard specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations.
1394
[Page extract]
Why is double lap shear testing important?
The double lap shear test is widely used to determine the performance of adhesives in structural and semi-structural applications. It allows engineers to:
1395
[Page extract]
Cosmetics & Personal Care Products
Mecmesin solutions for testing in cosmetics and personal care.
Test product formulation for objective texture analysis as well as applicators, dispensers and packaging.
1396
[Page extract]
Introduction to closure torque testing
Closure torque testing measures the rotational force required to apply or remove a closure, such as a bottle cap, jar lid, or other sealing component, from its container.
1397
[Page extract]
ASTM F1306
ASTM F1306, is a test method, which permits flexible barrier films and laminates to be characterised for slow rate penetration resistance to a driven probe.
1398
[Page extract]
Simplify data analysis in force, materials and torque testing
Test calculations are the values derived from raw measurement data, such as peak force, torque angle, or modulus of elasticity. With advanced software, these are now calculated instantly and with high precision, replacing error-prone manual methods.
1399
[Page extract]
ASTM D7078/D7078M-12
This test method covers the determination of the shear properties of high-modulus fiber-reinforced composite materials by clamping the ends of a V-notched specimen between two pairs of loading rails.
1400
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.