Search results
1576
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1577
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1578
[Page extract]
TAPPI T 825
The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.
1579
[Page extract]
ASTM D7030-04
This test method covers determining the resistance of an empty paper corrugated shipping container to a vertically applied constant compression load for a specified time.
1580
[Page extract]
BS EN 2307
Ropes, Fibre ropes, Mechanical testing, Tensile testing, Dimensional measurement, Rope pitch, Elongation, Breaking load, Physical testing, Water-resistance tests, Mass, Linear density, Density measurement
1581
[Page extract]
*corp Mastercard CQM: ID-1
Mastercard CQM requirement covers Peel Strength Test (TM-412 #8120#) and Advanced Peel Strength Test (TN-424 #8240#). Methods are based around ISO 10373-1 to determine the peel strength between 2 layers of an ID or security card.
1582
[Page extract]
BS EN 20594-1
Conical fittings (syringes), Syringes, Injection instruments, Medical instruments, Medical equipment, Tapered, Dimensions, Surgical instruments, Leak tests, Pressure testing, Mechanical testing, Torsion testing
1583
[Page extract]
ASTM D2095
This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing.
1584
Case study
Smoke grenade canister integrity
Customised engineering example
A manufacturer of smoke grenades required a means of testing the cap pull-off strength. The particular challenge was to grip the smooth metal cylinder for up to 5 kN of pulling force.
1585
[Page extract]
SAE AMSSTD
This standard covers the general requirements and methods for testing sandwich core materials and for testing sandwich construction of the types used primarily in aircraft structures.
1586
Case study
Resistência à punção do recipiente para objetos cortantes médicos
Exemplo de engenharia customizada Os padrões internacionais (ASTM F2132, BS 7320) especificam a resistência à perfuração de recipientes para perfurocortantes médicos.
1587
[Page extract]
BS 4863
Gives safety requirements for playpens for use by children up to 15kg in weight. It covers both rigid sided and mesh sided playpens.
1588
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
1589
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile
1590
Case study
Pump dispenser bottle operation
Customised engineering example
As a method to dispense liquids and sprays propellants, such as pressurised gas, are avoided for many reasons. Dispensers with manual spring-loaded pumps are often used in their place.
1591
[Page extract]
BS EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
1593
[Page extract]
ASTM F152-95
ASTM F152 is a test standard that covers tensile strength of nonmetallic gasketing materials at room temperature.
1594
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1595
[Page extract]
BS EN ISO 4624
Describes methods for determining the adhesion by carrying out a pull-off test on a single coating or a multi-coat system of paint, varnish or related product.
1596
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
1597
[Page extract]
IEC 61730-2
The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.
1598
[Page extract]
ASTM F963-17
This specification relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a toy is intended or after reasonably foreseeable abuse.
1599
[Page extract]
BS EN ISO 9626
This International Standard specifies the dimensions, surface and mechanical properties of normal- and thin-walled tubing of designated metric sizes 3,4 mm to 0,3 mm, and of extra-thin-walled tubing of designated metric sizes 2,1 mm to 0,6 mm.