Search results
2176
[Page extract]
ISO 3781
Specifies a test method for the determination of the wet tensile strength of paper or board after its immersion in water for a specified period.
2177
[Page extract]
BS 1726-2
Springs, Helical springs, Cylindrical shape, Tensile loading, Circular shape, Wires, Bars (materials), Parallel, Dimensional tolerances, Form tolerances, Product specification, Ordering, Mechanical testing, Heat treatment
2178
[Page extract]
ISO 9727-2
This part of ISO 9727 specifies a test method for:
⎯ measuring the mass of cylindrical cork stoppers ready for use or semi-worked, totally or partially made of agglomerated cork, and
2179
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
2180
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
2181
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.
2182
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
2183
[Page extract]
ISO 9727-5
Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.
2184
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
2185
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
2186
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
2187
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
2188
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
2189
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
2190
[Page extract]
CETIE Guide 18
This document provides a collection of test methods for the qualification of plastic flat-top closures applied on PET bottles that are used in the beverage industry.
2191
[Page extract]
SAE J 1553
This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.
2192
[Page extract]
MIL AS23190A
AS23190 is a procurement specification that covers a series of plastic and metal components and devices used for the tying, positioning, and supporting cable, cable assemblies, wire, and wire bundles in electrical, electronic and communication equipment
2193
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
2194
[Page extract]
EN 149
EN149 specifies minimum requirements for filtering half masks as respiratory protective devices to protect against particles except for escape purposes.
2195
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
2196
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
2197
[Page extract]
ASTM D4562-01
This test method covers the determination of the shear strength of curing liquid adhesives used for retaining cylindrical assemblies or for locking and sealing threaded fasteners.
2198
[Page extract]
BS EN 1271
Balls (sports equipment), Ball-games equipment, Sports nets, Dimensions, Design, Classification systems, Performance, Breaking load, Yarn, Cords, Grades (quality), Safety measures, Mechanical testing, Instructions for use, Marking, Foundations, Anchorag
2199
[Page extract]
BS EN ISO 10074
Aluminium, Aluminium alloys, Coated materials, Anodizing, Anodic coating, Coatings, Thickness, Density, Surface defects, Classification systems, Oxides, Inspection, Grades (quality), Wear resistance, Hardness, Corrosion resistance, Wear tests, Specimen