Search results
1976
[Page extract]
BS EN 50289-3-9
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Flexural strength, Bending stress, Bend testing, Stiffness
1977
Case study
열기구 천 인장 강도 및 인열 저항 테스트
요구 사항 Ultra Magic은 세계에서 두 번째로 큰 열기구 제조업체입니다. 명백한 안전상의 이유로 사용되는 재료는 항공 산업에 적용되는 엄격한 표준을 준수해야합니다. 이를 위해 회사는 풍선 '봉투'의 여러 영역에서 사용되는 재료에 대해 통제 된 평가를해야합니다. Ultra Magic은 풍선 천에 인장 강도 테스트를 수행하는 테스트 시스템을 원했습니다.
1978
[Page extract]
ASTM D926-17
ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.
1979
[Page extract]
Interpreting test results
Peel strength is typically reported in newtons per metre (N/m) or per 25 mm of bond width (N/25mm), depending on the industry standard. From the force-displacement graph, the following characteristics are analysed:
1980
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
1981
[Page extract]
BS EN 2597
BS EN 2597 is test method covering tensile testing on carbon fibre reinforced plastics.
Before conducting BS EN 2597, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
1982
[Page extract]
ASTM F1044-05
This test method covers shear testing of continuous calcium phosphate coatings and metallic coatings adhering to dense metal substrates at ambient temperatures.
1983
[Page extract]
ISO 6922
Specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method is applicable to all types of adhesives.
1984
[Page extract]
BS EN ISO 205
Adhesives. Wood adhesives for non-structural applications. Determination of tensile shear strength of lap joints.
1985
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
1986
[Page extract]
BS EN 14477
Packaging, Packaging materials, Flexible materials, Perforating tests, Mechanical testing
1987
[Page extract]
BS EN 1895
Adhesives, Adhesion tests, Peeling tests, Paper, Paper products, Board (paper), Disposable, Packaging materials, Flexible materials
1988
[Page extract]
Why torque testing is essential in packaging
Prevents leakage in liquid containers
Ensures seal integrity and prevents contamination
Confirms child-resistant closures are effective and compliant
Improves user experience by avoiding over-tightening
<
1989
Event
Brütsch-Rüegger Tools at INNOTEQ 2025
Our trusted distributor, Brütsch-Rüegger Tools, will be exhibiting at INNOTEQ 2025 - the key event for Switzerland’s manufacturing industry.
1990
[Page extract]
Interpreting compressive strength test results
Interpreting results involves more than noting the peak load. Stress–strain curves reveal additional information such as modulus, yield point, and failure mode.
1991
[Page extract]
ASTM D4533-11
This test method is an index test used to measure the force required to continue or propagate a tear in woven or non-woven geotextiles by the trapezoid method.
1992
[Page extract]
BS EN ISO 1806
This standard specifies a method of determining the mesh breaking force of netting for fishing.
1993
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1994
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1995
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
1996
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
1997
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
1998
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
1999
[Page extract]
BS EN 12814-2
BS EN 12814-2 is a tensile test method for testing welded joints of thermoplastics semi-finished products.