Search results
1251
Page
You have been subscribed to the Mecmesin newsletter
Thank you
We hope you enjoy the regular updates on our developments in force, materials and torque testing.
1252
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
1253
[Page extract]
IEC 61730-2
The standard defines the basic safety test requirements and additional tests that are a function of the PV module end-use applications.
1254
[Page extract]
ASTM D695-15
ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.
1255
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile
1256
[Page extract]
BS EN 1263-1
Safety nets, Restraint systems (protective), Construction equipment, Safety devices, Building sites, Occupational safety, Performance, Man-made fibres, Polyamide fibres, Polyolefin fibres, Ropes, Performance testing, Mechanical testing, Tensile testing,
1257
[Page extract]
BS 6965-1
Cartons, Board (paper), Paper products, Crease-recovery tests, Creasing tests, Folding, Test equipment, Specimen preparation, Testing conditions, Reproducibility, Containers, Blanks, Stiffness, Boxboard
1258
Case study
Luer lock fastening and release torque
Customised engineering example
Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.
1259
Case study
Electrical connector insertion and withdrawal forces
Customised engineering example
Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.
1260
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1261
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
1263
[Page extract]
ASTM F963-17
This specification relates to possible hazards that may not be recognized readily by the public and that may be encountered in the normal use for which a toy is intended or after reasonably foreseeable abuse.
1264
[Page extract]
BS EN ISO 8510-2
Adhesives, Adhesive-bonded joints, Adhesion tests, Flexible materials, Peeling tests, Test equipment, Specimen preparation, Test specimens
1265
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
1266
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1267
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1268
[Page extract]
EN 22872
EN 22872 specifies two methods for testing complete, filled transport packages for compression resistance.
1269
[Page extract]
BS EN 2307
Ropes, Fibre ropes, Mechanical testing, Tensile testing, Dimensional measurement, Rope pitch, Elongation, Breaking load, Physical testing, Water-resistance tests, Mass, Linear density, Density measurement
1270
Case study
바늘 대 페룰 풀 아웃 테스트
요구 사항 고객 인 Oxford Instruments는 두 부품을 분리하기위한 최대 장력을 평가하기 위해 파괴적인 풀 아웃 테스트를 수행하기를 원했습니다. 이 시스템은 피하 주사 바늘 끝에있는 주름진 페룰의 인장 무결성을 확인하도록 설계되었습니다.
1271
[Page extract]
BS EN ISO 10555-5
Catheters, Cannulas, Sterile equipment, Parenteral infusion equipment, Medical instruments, Medical equipment, Disposable, Colour codes, Preferred sizes, Diameter, Syringes, Flow rates, Packaging, Tensile testing, Mechanical testing, Testing conditions,
1272
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
1273
[Page extract]
Customised testing equipment and fixtures
Mecmesin testing systems are highly versatile and we specialise in conquering force and torque testing challenges of all sizes.
1274
[Page extract]
ASTM D885/D885M-10a
These [comprehensive] test methods cover the testing of industrial filament yarns made wholly of manufactured organic-base fibers, cords twisted from such yarns, fabrics woven from such cords, and products that are made specifically for use in the manuf
1275
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of