Search results
1351
[Page extract]
How to conduct a grab test
A standard grab test involves the following steps:
1352
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1353
[Page extract]
ASTM F1839-08
This specification covers rigid polyurethane foam blocks or sheets recommended for use as a standard material for mechanical testing using orthopedic devices and instruments.
1354
[Page extract]
ASTM C1292
This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at ambient temperature.
1355
[Page extract]
Three-point vs four-point bend testing
In a three-point bend test, force is applied at a single midpoint. In a four-point bend test, two loading noses distribute the load over a larger section of the specimen.
1356
Event
Brütsch-Rüegger Tools at INNOTEQ 2025
Our trusted distributor, Brütsch-Rüegger Tools, will be exhibiting at INNOTEQ 2025 - the key event for Switzerland’s manufacturing industry.
1357
[Page extract]
Introduction to chord modulus
Chord modulus is a key parameter in material testing, providing engineers and quality control teams with a precise measure of a material’s stiffness under defined loading conditions.
1358
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1359
[Page extract]
Measurement and testing methods
Techniques for measuring tangent modulus
Tangent modulus is measured during tensile or compression testing, w
1360
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1361
[Page extract]
Introduction to insertion and withdrawal testing
Insertion and withdrawal testing is a critical method for evaluating the performance, durability, and reliability of components that require secure and repeatable connections.
1362
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
1363
[Page extract]
BS EN 62275
This International Standard specifies requirements for metallic, non-metallic and composite cable ties and their associated fixing devices used for the management and support of wiring systems in electrical installations.
1364
[Page extract]
Why is double lap shear testing important?
The double lap shear test is widely used to determine the performance of adhesives in structural and semi-structural applications. It allows engineers to:
1365
[Page extract]
*corp 01M-01-216
To determine the maximum force required to rupture (break) a woven fabric – Rugby only
1366
[Page extract]
FAQs about compressive strength testing
How is compressive strength different from tensile strength?
1367
[Page extract]
Why Mecmesin for puncture resistance testing
Mecmesin designs and manufactures precision puncture resistance testing systems to meet the requirements of ASTM and ISO standards.
1368
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1369
[Page extract]
BS ISO 11193-1
ISO 11193-1:2008 specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves intended for use in medical examinations and diagnostic or therapeutic procedures to protect the patient and the user from cross-contamination.
1370
[Page extract]
ASTM D4501-01
This test method describes a procedure and fixture used to determine shear strengths of adhesives used to bond materials with moduli higher than the modulus of the adhesive.
1371
[Page extract]
What is lap shear testing under compression?
Lap shear testing under compressive load is a mechanical test used to determine the strength of
1372
[Page extract]
Introduction to Delft tear testing
The Delft tear test is a specialised method for determining the tear strength of vulcanised rubber, thermoplastic elastomers and similar flexible materials.
1373
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
1374
[Page extract]
Coefficient of friction (COF) explained
Understanding the COF formula
The coefficient of friction (μ) is a dimensionless value calculated as:
1375
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co