Search results
1251
[Page extract]
Standards for bulk analysis testing
Applicable standards and protocols
To ensure consistency and regulatory compliance, bulk testing is often carried out in accordance with established standards. These include:
1252
[Page extract]
ASTM F2458-05
This test method covers a means for comparison of wound closure strength of tissue adhesives used to help secure the apposition of soft tissue.
1253
[Page extract]
Introduction to tensile testing
Tensile testing is one of the most widely used methods in material science for determining the mechanical properties of materials under uniaxial tension.
1254
[Page extract]
Introduction to yield point testing
Yield point testing is essential for understanding the mechanical behaviour of materials.
1255
[Page extract]
Importance of ergonomic strength testing
Ergonomic strength testing is essential for ensuring that human performance matches task requirements. This alignment reduces the risk of musculoskeletal injuries and improves long-term health outcomes.
1256
[Page extract]
Torque testing standards
A range of recognised standards define the correct procedures for reverse ratchet torque testing, ensuring consistent and reliable results.
1257
[Page extract]
MIL 22520-G
This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielde
1258
[Page extract]
Understanding compressive and tensile forces
Insertion and withdrawal testing focuses on two key force measurements:
1259
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1260
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.
1261
[Page extract]
Mecmesin equipment for 90-degree peel testing
Mecmesin provides a range of test systems designed for peel and adhesion applications:
1262
Bundle
Sharps puncture tester
OmniTest 2.5
BD001
A tester designed for key international standards such as ASTM F2132, BS 7320, and BS 23907 that specify the test procedures for puncture resistance of medical sharps containers.
1263
[Page extract]
Introduction to fabric testing
Fabric testing plays a critical role in quality assurance, helping manufacturers assess the mechanical, physical, and chemical properties of textile materials.
1264
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1265
[Page extract]
ISO 2493-1
Specifies procedures, based on the two-point loading principle, for determining the bending resistance of paper and board.
1266
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1267
[Page extract]
Speak to an expert
Selecting the right trapezoidal tear testing setup requires understanding both the material and the relevant standards.
1268
[Page extract]
ISO 13445
Specifies a method for the determination of the shear strength of adhesives used to bond materials with elastic moduli higher than the elastic modulus of the adhesive.
1269
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
1270
[Page extract]
Three-point vs four-point bend testing
In a three-point bend test, force is applied at a single midpoint. In a four-point bend test, two loading noses distribute the load over a larger section of the specimen.
1271
Test Frame
OmniTest test frame (single column)
OmniTest test frame
A single-column motorised test frame designed to apply tensile, shear, flexural and compressive forces from 2 N right up to a capacity of 7.5 kN (1686 lbf).Its versatile construction makes it perfectly suited for testing all kinds of…
1272
[Page extract]
Key properties measured in tensile testing
While ultimate tensile strength is the headline result, tensile testing also measures:
1273
[Page extract]
ASTM F1839-08
This specification covers rigid polyurethane foam blocks or sheets recommended for use as a standard material for mechanical testing using orthopedic devices and instruments.
1274
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.