Mecmesin | Search results

1876

^{[Page extract]}

ASTM D412-16

ASTM D412 is a test standard for testing the tensile stress-strain properties of thermoset rubbers and thermoplastic elastomers. The standard is divided into two test methods.

1877

^{[Page extract]}

ASTM F2256-05

This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.

1878

^{[Page extract]}

This test method covers the determination of the core shear properties of flat sandwich constructions subjected to flexure in such a manner that the applied moments produce curvature of the sandwich facing planes.

1879

^{[Page extract]}

BS EN ISO 8295

ISO 8295 specifies a method for determining the coefficients of starting and sliding friction of plastics film and sheeting when sliding over the same or other substances. It is intended to be used for non-sticky plastic film and sheeting of up to appr

1880

Product

고급 힘 및 토크 표시기

AFTI

851-401

높은 정확도와 유연성을 제공하는 교체 가능한 '스마트'센서가있는 다용도 힘 및 토크 디스플레이 장치. AFTI 는 모바일 애플리케이션을위한 핸드 헬드 장치로 사용되거나 자체 테스트 장비에 통합하기위한 측정 장치로 사용될 수 있습니다.

1881

^{[Page extract]}

ASTM D3164

Test method ASTM D3164 is used to produce shear strength data for joints to compare adhesives or evaluation surface treatments. Shear joints impose uniform stresses across the bond area which results in the highest possible joint strength.

1882

Event

Wire Crimp & Weld Testing Webinar

The only way of really knowing the strength of a crimped terminal is to pull it.

1883

^{[Page extract]}

ASTM D5379/D5379M-05

This test method covers the shear properties of composite materials reinforced by high-modulus fibers. The composite materials are limited to continuous-fiber or discontinuous-fiber-reinforced composites in specific forms.

1884

^{[Page extract]}

ASTM D6415 / D6415M-06a

ASTM D6415 is designed to measure the curved beam strength properties of fiber reinforced composites using a 90˚ curved beam specimen. The curved beam strength represents the moment per unit width which causes a delamination to form.

1885

^{[Page extract]}

ISO 13954

ISO 13954 describes a peel test method for determining the decohesive resistance of polyethylene electrofusion socket assemblies for use in the distribution of fluids.

1886

^{[Page extract]}

ASTM C165

1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.

1887

^{[Page extract]}

ASTM D 2979

1.1 This test method covers measurement of the pressure sensitive tack of adhesives.

1888

^{[Page extract]}

TAPPI T 400

This method describes procedures for obtaining a representative sample for testing.

1889

^{[Page extract]}

TAPPI T 840

This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.

1890

^{[Page extract]}

BS EN 14350-1

Resusable teats and drinking accessories Resusable feeding bottles and drinking cups Single use feeding bottles, feeding teats, feeding bags and drinking accessories, which do not contain fluid when purchased.

1891

^{[Page extract]}

BS EN ISO 7886-1

This document specifies requirements and test methods for verifying the design of empty sterile single use hypodermic syringes, with or without needle, made of plastic or other materials and intended for the aspiration and injection of fluids after fill

1892

^{[Page extract]}

ISO 9073-3

Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.

1893

^{[Page extract]}

BS EN 28510-1

Test for measuring resistance to peeling at a nominal 90°, particularly suitable for adherends that are insufficiently flexible for a 180° peel test.

1894

^{[Page extract]}

ASTM D3983

This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.

1895

^{[Page extract]}

ISO 1805

ISO 1805 specifies a method of testing the breaking force and knot breaking force of netting yarns for fishing nets.

1896

^{[Page extract]}

SAE J 1553

This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.

1897

^{[Page extract]}

BS 6319-11

BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction

1898

^{[Page extract]}

TAPPI T 825

The flat crush test (1) is a measure of the resistance of the flutes in corrugated board to a crushing force applied perpendicular to the surface of the board under prescribed conditions.

1899

^{[Page extract]}

ASTM C297

This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.

1900

^{[Page extract]}

BS EN ISO 3386

BS EN ISO 3386-1 specifies a method for the determination of the compression stress/strain characteristic of low-density flexible cellular materials up to 250 kg/m3.

Search results

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

[Page extract]

시스템

악기

시스템

악기

시스템

악기

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}

^{[Page extract]}