Search results
2251
[Page extract]
ASTM D6534-05
This test method covers the determination of the peak force-to-actuate, sometimes called force-to-actuate (FTA), of a mechanical pump dispenser.
2252
[Page extract]
BS EN 863
Protective clothing, Clothing, Perforating tests, Penetration tests, Mechanical testing, Tensile testing, Test equipment, Specimen preparation, Performance testing
2253
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
2254
[Page extract]
BS EN ISO 13002
Carbon fibres, Designations, Filament yarns, Filament (textile fibre), Textile fibres, Filaments, Reinforcing materials, Polymers, Plastics, Reinforced materials, Composite materials, Data blocks, Tensile strength, Modulus of elasticity, Linear density<
2255
[Page extract]
ISO 12236
Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
2256
[Page extract]
ISO 1924-3
Specifies a method for measuring the tensile strength, strain at break, tensile energy absorption and tensile stiffness, using a testing machine operating with a constant rate of elongation (100 mm/min).
2257
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
2258
[Page extract]
ASTM F1566-09
These test methods cover recognized methods for testing mattress innersprings, boxsprings, and finished mattresses or mattress sets, or both, to ensure uniformity of results.
2259
[Page extract]
ISO 4587
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
2260
[Page extract]
ISO 8362-7
This part of ISO 8362 specifies aluminium-plastics combinations for the injection caps of injection vials, as specified in ISO 8362-1 and ISO 8362-4, where the plastics part does not overlap the diameter of the vial body. Section 6.2 Force required to
2261
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
2262
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
2263
[Page extract]
ISO 11607-1
Specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.
2264
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2265
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
2266
[Page extract]
ASTM D1002
This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
2267
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2268
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
2269
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
2270
Case study
크리켓 볼 압축 변형 강도 및 커버 재료 인장 강도
요구 사항 Kookaburra는 크리켓 및 하키 용 스포츠 장비 생산 분야에서 국제적으로 인정받는 리더입니다. 1890 년에 설립 된이 회사는 혁신과 품질에 대한 세심한 관심을 바탕으로 이름을 쌓았습니다. 기술 혁신의 길을 지속적으로 선도하는 능력에있어 가장 중요한 것은 완제품과 세계적 수준의 장비를 만드는 천연 재료의 품질을 쉽고 안정적으로 정량화 할 수있는 능력입니다.
2271
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
2272
[Page extract]
Why Mecmesin for breakaway torque testing?
Mecmesin offers an unmatched combination of reliability, support, and industry insight:
2273
[Page extract]
ASTM D1876
This test method measures the peel separation strength of two flexible materials that have been bonded together.
2274
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2275
[Page extract]
BS EN 1155
Closing and check mechanisms, Door closers, Electrically-operated devices, Ironmongery (buildings), Classification systems, Design, Performance, Durability, Temperature-rise limit, Test equipment, Sampling methods, Performance testing, Temperature, Elec