Search results
2351
[Page extract]
ASTM D2095
This test method covers the determination of the relative tensile strength of adhesives by the use of bar- and rod-shaped butt-joined specimens under defined conditions of preparation, conditioning, and testing.
2352
[Page extract]
BS 6319-3
BS 6319-3 is a test method for determining the modulus of elasticity in flexure and flexural strength of resin and polymer/cement compositions for use in construction.
2353
[Page extract]
BS EN 12814-4
BS EN 12814-4 is a peel test method for testing welded joints of thermoplastics semi-finished products.
2354
[Page extract]
ASTM D4475-02
ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.
2355
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
2356
[Page extract]
IEC 60371-2
Part 1 is definitions of general requirements
Part 3 specifications for individual materials
A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.
2357
[Page extract]
ASTM D7030-04
This test method covers determining the resistance of an empty paper corrugated shipping container to a vertically applied constant compression load for a specified time.
2358
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
2359
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
2360
[Page extract]
ASTM D5672-09
This test method covers a screening type quality control test used to determine if flexible polyurethane foam cushions are within the specified grade range for firmness.
2361
[Page extract]
BS EN ISO 10555-5
Catheters, Cannulas, Sterile equipment, Parenteral infusion equipment, Medical instruments, Medical equipment, Disposable, Colour codes, Preferred sizes, Diameter, Syringes, Flow rates, Packaging, Tensile testing, Mechanical testing, Testing conditions,
2362
[Page extract]
ASTM C203
ASTM C203 is a test method that covers the determination of the breaking load and calculated flexural strength of a rectangular cross section of a preformed block-type thermal insulation tested as a simple beam.
2363
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
2364
[Page extract]
ASTM D747-10
ASTM D747 is used to determine the flexibility of plastics by means of a cantilever beam.
2365
[Page extract]
ASTM C582
This specification covers composition, thickness, fabricating procedures, and physical property requirements for glass fiber reinforced thermoset polyester, vinyl ester, or other qualified thermosetting resin laminates comprising the materials of constr
2366
[Page extract]
BS EN 12814-3
BS EN 12814-3 is a tensile creep test method for testing welded joints of thermoplastics semi-finished products.
2367
[Page extract]
Young's modulus
Measure how stiff or elastic a material is under tension or compression with Young’s modulus testing. Universal testing systems provide reliable modulus of elasticity measurements for compliance with global standards like ISO 527 and ASTM D638.
2368
[Page extract]
Baumann tear test
- slit cut laterally in the centre of sample; used to test the tear strength of leather
2369
[Page extract]
Ultimate Tensile Strength
What it is, how to measure it, and why it matters
Ultimate tensile strength (UTS) is a critical property used to determine how materials behave under tension. It defines the maximum stress a material can withstand before breaking.
2371
[Page extract]
Shear Modulus Guide
Understanding how a material behaves under sliding or twisting forces is essential when selecting the right component for mechanical or structural performance.
2372
[Page extract]
Hospitals
Mecmesin provides force, materials and torque testing equipment for medical and dental hospitals and their associated teaching institutions.
2373
[Page extract]
Elongation and Recovery
Elongation and recovery testing is a fundamental process in material science used to measure how far a material can stretch under a given load and how effectively it returns to its original shape once the force is removed.
2374
[Page extract]
Jewellery & Watch
In jewellery and watch production, alloys, components and other materials must meet the needs of the manufacturing process and the end-product should give good service performance when worn by the customer.
2375
Case study
기폭 장치 충격 튜브
요구 사항 산업용 애플리케이션을위한 비-전기 충격 기폭 장치 튜빙 제조업체는 전문적인 인장 테스트 요구 사항이있었습니다. 폭발물을 시작하기 위해 긴 표면 네트워크에 배치 된 고강도 나일론 튜브는 신뢰성과 정확한 타이밍을 위해 가장 거친 환경에서 무결성을 유지해야합니다.