Search results
576
Accessory
Blank (smooth) Inset Jaws for MEC9 Thin Wire Grip, 2.5 kN
Mec9-EB
MEC9-EB Blank Jaws
Blank (smooth) inset jaws of 37 mm height x 15 mm width, 0.5 set. For fitting into the carrier of the MEC9 Thin Wire Grip.
Used when jaws require a specific surface to be machined onto them. Alternatively for affixing an abrasive…
577
Accessory
Upper Precision Fixing Plate for Helixa sensors
432-601
Precision Upper Fixing Plate for Helixa.
Mounts onto the square-drive of Helixa torque sensors. Fitted with a precision leadscrew and sprung-loaded runners into which jaws or holding pegs can be inserted (order separately). Tighten the knob to secure…
578
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 30 mm
Mec240k-BD
Diamond Jaws (30mm x 30mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
579
Accessory
Cable Cam grip for CrimpTest-1 kN
432-660
Cable Cam Grip for CrimpTest-1 Tester (supplied as standard with the Tester)
The Cable Cam Grip is designed for holding insulated cables and wire when tensile testing the pull strength of terminals up to 1 kN.
The cable is secured by the serrated cam,…
580
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 80 mm
Mec240k-BD80
Diamond Jaws (30mm x 80mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
581
Case study
Medical suture device calibration system
Requirement
A number of devices which 'crimp' a curved needle to a fine medical thread needed to be tested. The crimp force was applied horizontally pulling a lever on the device.
582
Accessory
Pyramid jaws for Mec11-20 Scissor Grip, 10 kN, 25 x 100 mm
Mec11-20-BP100
Pyramid Jaws (25mm high x 100mm wide) - nickel-plated having a surface of hardened steel pyramids of 1.2mm tall. By using 100 mm width jaws tensile force is reduced to 10kN.
For materials which need a “bite” to secure a good grip (e.g. soft metals {…
583
Accessory
Thin Wire Grip with carrier for inset jaws, 2.5 kN, QC-20 fitting
Mec9
MEC9 Thin Wire Grip
Designed to hold wires or cords when tensile testing up to 2.5 kN.
The specimen is initially wrapped around a bollard and then secured by manually clamping between either blank or diamond-coated jaws. The Mec9 is supplied with the…
584
Case study
Child safety - force to extract lighter
Requirement
The customer manufactures lighters and is currently developing a case/guard designed to increase the safety for children.
585
Accessory
Charger for touchscreen digital gauges, USA, USB-A, USB-C, 2-pin flat
304-072
For use with Mecmesin touchscreen digital force and torque gauges. With 2 flat pins. Commonly used in the USA.
The mains adaptor/charger is a USB-A, USB-C type:
Input: 100-240V~50/60Hz 0.5A
Output-C: 5.0V=3.0A; 9.0V=2.22A; 12.0V=1.5A
Output-A: 3.6-6.…
586
Accessory
FPT COF sled 200g (foam) for ASTM D1894 and ISO 8295
432-638
A foam-faced sled with magnetic grips, for testing coefficient of friction of plastic film samples to ASTM D1894 and ISO 8295. Supplied with rigid and extensible links.
For use on the FPT-H1 Friction Tester.
587
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 80 mm
Mec240k-BG80
Rubber-faced Jaws (30mm x 80mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
588
[Page extract]
Introduction to compressibility and recovery testing
Compressibility and recovery testing measures how a material behaves under load and how effectively it returns to its original form once the load is removed.
589
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 50 mm
Mec240k-BD50
Diamond Jaws (30mm x 50mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
590
[Page extract]
Standards and guidelines
Accurate and comparable cleavage strength testing depends on following recognised international standards.
591
Accessory
Charger for digital gauges, USA, 110 V/115 V, 2-pin flat
304-006
For use with Mecmesin digital force and torque gauges. 110 Volt with 2 flat pins. Commonly used in USA, Canada, Mexico and Japan.
The mains adaptor/charger is a constant-current type:
Primary circuit: 110V – 50-60Hz
Secondary circuit: 100mA constant…
592
Accessory
Digital Height Scale and Brackets for LCP/S Test Stand
432-162 V01
Digital Height Scale and Brackets for mounting to the lever-operated Manual Test Stand model LCP/S.
The digital display of the height-scale is fixed to the moving crosshead of the test stand so that it's displacement can be monitored. This is often…
593
Case study
Torque tester for windows and sunroof controls
Requirement
The customer requested a portable system which would quickly and easily allow him to test the torque required to open and close windows in a car.
594
Accessory
Large Single-action Vice Grip, wave-form, 2 kN, QC-20 fitting
432-267-V02
A Large Single-action Vice Grip featuring one fixed jaw and one jaw as freely adjustable to mechanically clamp the specimen in place.
Rated to 2 kN in tension with wave-form jaws of 78mm wide x 28mm high having an opening of 0 - 6.5 mm. Provides…
595
Case study
Metal bottle cap on glass pull-off test
Customised engineering example
Gripping the base of a glass bottle for a tensile test can be challenging due to the slippy surface and contoured shape.
596
Accessory
Pyramid jaws for Mec11-20 Scissor Grip, 10 kN, 25 x 100 mm
Mec11-20-BP100
Pyramid Jaws (25mm high x 100mm wide) - nickel-plated having a surface of hardened steel pyramids of 1.2mm tall. By using 100 mm width jaws tensile force is reduced to 10kN.
For materials which need a “bite” to secure a good grip (e.g. soft metals {…
597
Accessory
FINAT 2 Assisted Pull-Peel Table, 90 degrees, adjustable rails for float glass, QC-20
PDV15031
The FINAT 2 Assisted Pull-Peel table (90° Peel Test) is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of…
598
Accessory
Charger for touchscreen digital gauges, Europe, USB-A, USB-C, 2-pin round
304-067
For use with Mecmesin touchscreen digital force and torque gauges. With 2 round pins. Commonly used in the Europe.
The mains adaptor/charger is a USB-A or USB-C type:
Input: 100-240V~50/60Hz 0.5A
Output-C: 5.0V=3.0A; 9.0V=2.22A; 12.0V=1.5A
Output-A: 3…
599
Accessory
FINAT 2 Assisted Pull-Peel Table, 90 degrees, adjustable rails for float glass, QC-20
PDV15031
The FINAT 2 Assisted Pull-Peel table (90° Peel Test) is fitted to the anvil plate of a motorised test stand and then connected to the crosshead of a test stand. It is commonly used for conducting peel tests on adhesive tapes and films.
The carriage of…
600
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 50 mm
Mec240k-BG50
Rubber-faced Jaws (30mm x 50mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…