Search results
2151
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2152
[Page extract]
ISO 4587
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
2153
[Page extract]
ASTM D6049-03
This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular wei
2154
Event
Fundamentals of Cork Pull & Elasticity Testing
Natural corks need to execute several important functions within the champagne and wine industries in order to meet consumers’ expectations and also to guarantee the quality of the drink.
2155
[Page extract]
ISO 11607-1
Specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.
2156
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2157
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2158
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
2159
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
2160
[Page extract]
BS EN ISO 8670-2
Two part test on filled bags:
1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate
2161
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
2162
Specials
Touchscreen Controller VectorPro
Touchscreen Controller
The Touchscreen Controller has been designed for use with the Twin-column OmniTest range of Materials Testers as an alternative to a desktop or laptop PC.
2163
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2164
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
2165
[Page extract]
BS EN 1155
Closing and check mechanisms, Door closers, Electrically-operated devices, Ironmongery (buildings), Classification systems, Design, Performance, Durability, Temperature-rise limit, Test equipment, Sampling methods, Performance testing, Temperature, Elec
2166
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2167
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2168
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2169
[Page extract]
BS EN ISO 19011:2011
Provides the fundamental knowledge needed for auditing management systems and has been expanded to reflect modern thinking and the intricacies of auditing multiple management system standards (MSS).
2170
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
2171
[Page extract]
ISO 23910
ISO 23910 specifies a method for determining the stitch tear resistance of leather. It can be used on all leathers but is particualy suitable for leathers over 1.2 mm in thickness
2172
[Page extract]
Key standards for equibiaxial flexure testing
Internationally recognised standards ensure accuracy, repeatability, and comparability of results. Common references include:
2173
Case study
바늘 대 페룰 풀 아웃 테스트
요구 사항 고객 인 Oxford Instruments는 두 부품을 분리하기위한 최대 장력을 평가하기 위해 파괴적인 풀 아웃 테스트를 수행하기를 원했습니다. 이 시스템은 피하 주사 바늘 끝에있는 주름진 페룰의 인장 무결성을 확인하도록 설계되었습니다.
2174
[Page extract]
ASTM C273/C273M
This test method is used to determine core shear properties of a sandwich construction material using loading plates bonded to the outer surfaces or skins (facesheets).
2175
[Page extract]
BS EN ISO 13002
Carbon fibres, Designations, Filament yarns, Filament (textile fibre), Textile fibres, Filaments, Reinforcing materials, Polymers, Plastics, Reinforced materials, Composite materials, Data blocks, Tensile strength, Modulus of elasticity, Linear density<