Search results
2201
[Page extract]
ASTM F1566-09
These test methods cover recognized methods for testing mattress innersprings, boxsprings, and finished mattresses or mattress sets, or both, to ensure uniformity of results.
2202
Case study
Bow attachment pull-off test on clothing
Requirement
The customer was a supplier to major UK clothing retailer Marks & Spencer, who stipulate that all fasteners and attachments must be tested to failure.
2203
[Page extract]
ISO 1924-2
Specifies a method for measuring the tensile strength, strain at break and tensile energy absorption of paper and board, using a testing machine operating at a constant rate of elongation (20 mm/min).
2204
[Page extract]
BS EN 12365-2
Sealing materials, Weatherstrips, Gaskets, Performance, Classification systems, Windows, Doors, Rainwater control systems, Force measurement.
2205
[Page extract]
ISO 12192
Specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the manufacture of fibreboard shipping containers.
2206
[Page extract]
ASTM D2918
This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper
2207
[Page extract]
ISO 9727-4
ISO 9727-4 specifies a test method for determining the percentage of diameter recovery of cylindrical cork stoppers, after compression.
2208
[Page extract]
BS EN ISO 527-1
BS EN ISO 527-1 specifies the general principles for determining the tensile properties of plastics and plastic composites under defined conditions.
2209
[Page extract]
BS 7320
This British Standard specifies requirements for sharps containers intended to hold potentially infectious medical waste comprised largely of devices which can readily cause physical injury e.g. scalpel blades, hypodermic needles and syringes.
2210
[Page extract]
ISO 11502
Describes a qualitative and a quantitative method for assessing the tendency of flexible plastics films and sheets to adhere to one another when left in contact for some time, at a specified temperature and under light pressure.
2211
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
2212
Case study
関節強度の生理学的測定
要件メルボルンのラトローブ大学は、一般に足の親指として知られている最初の中足指節関節をテストするための装置を必要としていました。彼らは、異なる患者のつま先の強さを比較したかった。 Mecmesin Force Gaugesは、すでに労働安全衛生の用途と人間の努力の測定に使用されていたため、この用途に選択されました。
2213
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
2214
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2215
[Page extract]
SAE J 1523
This SAE Recommended Practice defines a procedure for determining shear strengths of adhesives used for bonding automotive oil metal substrates.
2216
[Page extract]
TAPPI T 804
This method is used for measuring the ability of corrugated or solid fiber shipping containers to resist external compressive forces.
2217
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
2218
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2219
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
2220
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2221
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2222
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
2223
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
2224
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
2225
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.