Search results
1951
[Page extract]
ASTM D229
ASTM D229 is a test method, which provides useful engineering information for evaluating the mechanical behaviour of rigid electrical insulation at elevated temperature.
1952
[Page extract]
SAE J1525
This SAE Recommended Practice describes a lap shear test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber reinforced plastics to themselves and to metals.
1953
[Page extract]
ASTM D2105
ASTM D2105 determines the comparative longitudinal tensile properties of fiberglass pipe when tested under defined conditions of pretreatment, temperature, and testing machine speed.
1954
[Page extract]
ASTM D4476 / D4476M-14
ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.
1955
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
1957
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.
1958
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
1959
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1960
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1961
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1962
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
1963
[Page extract]
ISO 8364
ISO 8364:2007 specifies requirements and test methods for the binding mounting area and free space area, ski bindings and retention devices of alpine skis, in order to optimize the compatibility of the functional unit "ski binding - retention device - b
1964
[Page extract]
BS EN 1607
This European Standard specifies the equipment and procedures for determining the tensile strength of a product perpendicular to its faces. It is applicable to thermal insulating products.
1965
[Page extract]
ASTM F2332-06
This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components.
1966
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
1967
[Page extract]
SAE AIR 1471A
The purpose of this SAE Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for commonly used aircraft propulsion system threaded fasteners when a common torque value per fastener si
1968
[Page extract]
BS 6319-6
BS 6319-6 is a test method for determining the modulus of elasticity in compression of resin and polymer/cement compositions for use in construction.
1969
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or
1970
[Page extract]
ASTM D2659
ASTM D2659 determines the mechanical properties of blown thermoplastic containers under columnar crush conditions at a steady rate of compression. Any container, whether blown commercially or in the laboratory, may be used as the test specimen.
1971
[Page extract]
BS EN ISO 10555-3
Catheters, Cannulas, Sterile equipment, Parenteral infusion equipment, Medical equipment, Medical instruments, Disposable, Marking, Flow rates, Force, Force measurement, Flow measurement, Test equipment, Testing conditions.
1972
[Page extract]
PSTC 101
These methods cover the measurement of the peel adhesion of pressure sensitive tapes.
1974
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
1975
[Page extract]
CETIE Guide 5
This document gives background information and recommended best practices for the application of plastic flat-top screw-on caps onto PET bottles for beverages. It covers all closure sizes and beverage product types.