Search results
2476
[Page extract]
BS EN ISO 3376
This International Standard specifies a method for determining the tensile strength , elongation at a specified load and elongation at break. It is applicable to all types of leather
2477
[Page extract]
ASTM D1414
ASTM D1414 is used to measure the mechanical properties of vulcanized rubber o-rings. Mecmesin test equipment is relevant to the tensile testing part of this standard, which covers a variety of different tests.
2478
[Page extract]
TAPPI T 821
Measures the force required to separate corrugated board between the flute tips of corrugated medium and its linerboard facings.
2479
[Page extract]
AEC Q200-005
This specification establishes the procedure and criteria to determine the ability of surface
mounted device terminations and seals to withstand bending, flexing and pulling forces which
2480
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2481
[Page extract]
Probes
Probes are designed primarily for penetration and puncture resistance testing. There are a variety of tip profiles and sizes available (e.g. cone, chisel, radiused) to simulate the real-world conditions under which a specimen may be compressed.
2482
Event
Materials Testing: Theory and Practice Pt. 1 & 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
2483
[Page extract]
ASTM E8/E8M-13a
These test methods cover the tension testing of metallic materials in any form at room temperature, specifically, the methods of determination of yield strength, yield point elongation, tensile strength, elongation, and reduction of area.
2484
[Page extract]
BS EN 319
EN319 specifies a method for determining the resistance to tension perpendicular to the plane of the board (“internal bond”) of particleboards, fibreboards, and cement-bonded particleboards.
2485
[Page extract]
BS EN ISO 6892-1
This part of ISO 6892 specifies the method for tensile testing of metallic materials and defines the mechanical properties which can be determined at room temperature.
2486
[Page extract]
NF B 57 100
Section 8 covers the measurement of the tensileforce to extract a natural or synthetic cork from a still wine bottle or from a standardised glass tube, which simulates the profile of the neck of a wine bottle.
2487
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2488
[Page extract]
BS 1726-3
Springs, Helical springs, Cylindrical shape, Torque, Circular shape, Wires, Bars (materials), Parallel, Dimensional tolerances, Form tolerances, Product specification, Ordering, Mechanical testing, Heat treatment
2489
[Page extract]
ASTM C364
This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.
2490
[Page extract]
ASTM D1000
These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:
Class 1—Non-elastomeric backings made from materials
2491
[Page extract]
CETIE Guide 12
This guide describes the five essential rules to be observed to properly crimp a pump with an aluminium ferrule on an FEA type glass finish used for perfumery, according to the EN 14854 standard and the Cetie document GME 40.05.
2492
Specials
Thermal cabinet environment chamber
Environmental chamber capability
Mecmesin's OmniTest twin column range can accommodate an environmental chamber to test materials in controlled ambient conditions.
2493
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
2494
[Page extract]
ASTM D3044
This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels.
2495
[Page extract]
ISO 12625-4
Specifies a test method for the determination of the tensile strength, stretch at break and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
2496
[Page extract]
BS 4839
Specification for Blow moulded polyolefin containers, part 2: Plastics containers. Containers over 5 litres and up to 60 litres capacity
2497
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2498
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
2499
[Page extract]
ASTM F1140/F1140M-13
These test methods provide a rapid means of evaluating tendencies for package failure when the package is exposed to a pressure differential. Pressure differentials may occur during processes such as sterilization and transportation.
2500
[Page extract]
ASTM C1028
This test method covers the measurement of static coefficient of friction of ceramic tile or other surfaces under both wet and dry conditions while utilizing Neolite heel assemblies. This test method can be used in the laboratory or in the field.