Search results
1401
[Page extract]
ASTM D2063/D2063M
This test method measures torque retention properties of container/continuous thread closure systems with the use of a non-automated, spring torque-meter (with either a dial indicator or a digital readout) or a torque wrench. evaluation.
1402
[Page extract]
ASTM F2458-05
This test method covers a means for comparison of wound closure strength of tissue adhesives used to help secure the apposition of soft tissue.
1403
[Page extract]
Introduction to single lap shear testing
Single lap shear testing is a widely used method for determining the shear strength of an adhesive bond between two overlapping materials.
1404
[Page extract]
Coefficient of friction (COF) explained
Understanding the COF formula
The coefficient of friction (μ) is a dimensionless value calculated as:
1405
Case study
Page pull strength test
Requirement
Mecmesin collaborated with a customer to design and develop a force measurement system to determine book binding adhesive strength in retaining individual pages.
1406
[Page extract]
Speak to an Expert
The Concora Crush Test, as defined in TAPPI T 824, is a critical step in corrugated medium evaluation.
1407
Accessory
Pyramid (serrated) jaws for Mec227 Lightweight Vice Grip, 100 N, 10 x 100 mm
Mec227-BP100
Pyramid Jaws (10mm high x 100mm wide) - nickel-plated having a surface of hardened steel pyramids of 1.2mm tall.
Opening span = 0 - 6mm.
For materials which need a “bite” to secure a good grip (e.g. soft metals - aluminium, copper, soft steel, paper…
1408
Accessory
Spare set of 15 needles for Shotcrete Penetrometer
432-519
Set of 15 Penetration Needles for use with the Mecmesin Shotcrete Pentrometer.
Needles fit into the needle-holder supplied as standard with the Shotcrete Penetrometer
1409
Accessory
QC Type L Adapter, 32 mm M, c/w pin and fixing screws
432-451
QC Male Post 32mm c/w cross-pin, locking collar…
1410
[Page extract]
ASTM F1342
This test method evaluates puncture resistance of protective clothing materials which may include plastics or elastomeric films, coated fabrics, flexible materials, laminates, or textile materials.
1411
Accessory
Wave jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 80 mm
Mec240k-BW80
Wave Jaws (30mm x 80mm) - nickel-plated having a hardened steel surface of 5mm tall waves.
For flexible but slippy materials which need more surface contact to secure a good grip (e.g. textiles, fabrics and tissues).
Supplied as 0.5 set = 2 jaws (left…
1412
Case study
Champagne and sparkling wine cork twist extraction effort
Requirement
Solution
Test equipment
1413
Accessory
Wave jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 100 mm
Mec240k-BW100
Wave Jaws (30mm x 100mm) - nickel-plated having a hardened steel surface of 5mm tall waves.
For flexible but slippy materials which need more surface contact to secure a good grip (e.g. textiles, fabrics and tissues).
Supplied as 0.5 set = 2 jaws (left…
1414
Accessory
Rubber coated jaws for Mec154 Heavy-duty Vice Grip, 20kN, 40 x 100 mm
Mec154-BG100
Rubber-faced Jaws (40mm high x 100mm wide) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0 - 28 mm.
For specimens, which may get weakened by pinching at the contact-edge of the grip. (e.g. films, filaments, fibres and…
1415
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
1416
[Page extract]
Power and flexibility for your materials testing
Start measuring stress/strain, tensile, shear, flexure and compressive forces to evaluate your materials. It takes just a few minutes to create your own step-by-step test routines.
1417
[Page extract]
Understanding tensile strength in testing
Both pull-off and pull-out testing measure tensile strength, which is the maximum load a specimen can sustain under tension before failure.
1418
[Page extract]
Mecmesin solutions for T-peel testing
With decades of experience in materials testing, Mecmesin provides accurate, repeatable T-peel testing systems that meet ASTM D1876, ISO 113
1419
[Page extract]
Why choose Mecmesin for shear testing in tension
Mecmesin provides precision-engineered solutions for shear testing in tension, designed to meet ASTM, ISO, and
1420
[Page extract]
Equipment for burst testing
The right equipment depends on the container type, material, and applicable standard.
1421
[Page extract]
Common challenges and solutions
Material inconsistencies - Variations in fibre composition and moisture content between batches can affect results.
1422
[Page extract]
Real-time data analysis and reporting
Mecmesin’s software platform offers live monitoring and evaluation of test performance:
1423
[Page extract]
Importance of testing elasticity and ultimate strength
Elasticity determines how well a material returns to its original shape after stretching. Ultimate strength indicates the maximum stress it can withstand before failure.
1424
[Page extract]
Mecmesin equipment for 180 degree peel testing
Mecmesin provides a complete range of test solutions designed for accurate and repeatable peel strength measurement.
1425
[Page extract]
Understanding the stress-strain curve
The stress-strain curve is a primary tool for tensile strength analysis. It shows how a material responds to an increasing tensile load, providing detailed insights into its mechanical properties.