Search results
1476
Case study
ROPPボトルキャップ閉鎖トルクテスト
要件ブラザーズドリンクは、ロールオンピルファープルーフ（ROPP）とクラウンボトルキャップの両方を使用して、さまざまなアルコール飲料とノンアルコール飲料を製造および共同梱包しています。この家族経営の会社は、さまざまな革新的なフレーバーを生み出しており、飲み物の鮮度を維持することは、品質に対するうらやましい評判に不可欠です。
1477
Test Frame
MultiTest test frame (single column)
MultiTest test frame
A ballscrew-driven motorised test frame designed to apply tension and compression from 2 N right up to a capacity of 5 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing all kinds of components in a quality…
1478
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
1479
[Page extract]
CETIE Guide 9
This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on
1481
[Page extract]
ISBT PTC-00004
These ISBT (International Society of Beverage Technologists) Sport Closure test methods focus on child safety related parameters such as separation forces and choking hazards of closure components.
1482
[Page extract]
ASTM F458-13
This practice covers nondestructive testing of individual wire bonds made by either ultrasonic, thermal compression or thermosonic techniques.
1483
[Page extract]
ASTM F2606-08
This guide can be used to obtain force versus deflection or midspan bending moment versus midspan curvature curves for stents and stent systems subjected to three-point bending conditions.
1484
[Page extract]
BS EN 4057-401
Aircraft components, Cable ties, Electric cable systems, Holding devices, Electric wiring systems, Electric cables, Tensile testing, Mechanical testing
To be read in conjunction with BS EN 4057-100
1485
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1486
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1487
[Page extract]
BS EN ISO 527-2
ISO 527-2 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in ISO 527-1.
1488
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
1489
Event
Texture Testing for Bakery Applications
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1490
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
1491
Event
Tensile Testing: Pull Force & Break Strength
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1492
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
1493
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1494
[Page extract]
ISO 37
ISO 37 specifies a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers.
This test standard is equivalent to BS ISO 37.
1495
Event
Understanding Top-Load Testing - Live Application Demo
Packaging manufacturers use top-load or crush testing to ensure packaging integrity, and to eliminate material excess while maintaining quality.
1496
[Page extract]
BS 7907
BS 7907 gives recommendations for the design and manufacture of children’s clothing to promote mechanical safety. This standard is applicable to clothing intended for children up to 14 years of age.
1497
Event
2022 Medical Technology Ireland, Galway, Ireland - We would love to see you there!
Who should attend?
Quality Managers and design/product engineers involved in the development and production of medical and pharmaceutical devices and packaging.
What is the exhibition about?
1499
[Page extract]
BS EN ISO 80369-1
BS EN ISO 80369 “Small-bore connectors for liquids and gases in healthcare applications. Connectors for intravascular or hypodermic applications”.
This standard replaces BS EN ISO 594-1: 1986, BS EN 20594-1:1994, and BS EN 1707:1997.
1500
[Page extract]
ASTM D3950
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.