Search results
2251
[Page extract]
BS EN ISO 13002
Carbon fibres, Designations, Filament yarns, Filament (textile fibre), Textile fibres, Filaments, Reinforcing materials, Polymers, Plastics, Reinforced materials, Composite materials, Data blocks, Tensile strength, Modulus of elasticity, Linear density<
2252
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2253
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
2254
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
2255
[Page extract]
ASTM F1566-09
These test methods cover recognized methods for testing mattress innersprings, boxsprings, and finished mattresses or mattress sets, or both, to ensure uniformity of results.
2256
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
2257
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
2258
[Page extract]
BS EN 1155
Closing and check mechanisms, Door closers, Electrically-operated devices, Ironmongery (buildings), Classification systems, Design, Performance, Durability, Temperature-rise limit, Test equipment, Sampling methods, Performance testing, Temperature, Elec
2259
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
2260
[Page extract]
ISO 8362-7
This part of ISO 8362 specifies aluminium-plastics combinations for the injection caps of injection vials, as specified in ISO 8362-1 and ISO 8362-4, where the plastics part does not overlap the diameter of the vial body. Section 6.2 Force required to
2261
[Page extract]
ISO 5079
Describes method and conditions of test for the determination of the breaking force and elongation at break of individual fibres in the conditioned or wet state. The test is restricted to the use of constant-rate-of-extension testing apparatus.
2262
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
2263
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2264
[Page extract]
BS EN 12655
Gymnastics equipment, Sports equipment, Safety measures, Equipment safety, Classification systems, Dimensions, Height, Strength of materials, Stability, Mechanical testing, Vertical, Horizontal, Performance testing, Instructions for use
2265
[Page extract]
Why Mecmesin for breakaway torque testing?
Mecmesin offers an unmatched combination of reliability, support, and industry insight:
2266
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2267
[Page extract]
BS EN 863
Protective clothing, Clothing, Perforating tests, Penetration tests, Mechanical testing, Tensile testing, Test equipment, Specimen preparation, Performance testing
2268
[Page extract]
ASTM D1002
This test method covers the determination of the apparent shear strengths of adhesives for bonding metals when tested on a standard single-lap-joint specimen and under specified conditions of preparation and test.
2269
Case study
高性能プラズマコーティング
要件Alphatek Hyperformance Coatings Ltd.は、摩耗、腐食、熱、または電気抵抗性コーティングを適用するコーティング会社であり、さまざまな業界に供給しています。プラズマコーティングの品質は、基材への接着性に完全に依存しており、業界標準のASTMC633に準拠している必要があります。要件は、コーティングのテストサンプルを引き剥がすのに必要な力を決定することでした。
2270
[Page extract]
ASTM D642-00
This test method covers compression tests on shipping containers (for example, boxes and drums) or components, or both. Shipping containers may be tested with or without contents.
2271
[Page extract]
CETIE Guide 4
This document concerns the crowning process, using crown caps for which the seal is provided by a plastic liner, onto glass finishes adapted to either "pry-off" or "twist crown" applications.
2272
[Page extract]
ISO 12236
Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
2273
[Page extract]
ASTM D905-08
This test method covers the determination of the comparative shear strengths of adhesive bonds used for bonding wood and other similar materials, when tested on a standard specimen under specified conditions of preparation, conditioning, and loading in
2274
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
2275
[Page extract]
ASTM D7233-08
This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent.