Search results
2001
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
2002
[Page extract]
ASTM D1871
This test method is used to test the strength of adhesion of single-filament wire to vulcanized rubber compounds. It applies to wire made from brass, bronze or zinc coated steel wire.
2003
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.
2004
[Page extract]
ISO 7623
ISO 7623 specifies a method for determining the bond strength of metal cords to their surrounding coating, either in the initial state or after thermal treatment.
2005
[Page extract]
Jaws
Choosing the most appropriate jaw type for a tensile grip can be tricky. It is a balance between having sufficient hold of the specimen to prevent it slipping and not having too ‘aggressive’ a hold which damages the specimen.
2006
[Page extract]
ASTM D1566
ASTM D1566 is a source of reference for definitions of technical terms used in the rubber industry
Standards can be obtained from appropriate standard authorities.
2007
[Page extract]
TAPPI T 824
This test evaluates the ability of corrugating medium to contribute to the compression strength of a corrugated box.
2008
[Page extract]
ASTM D5379/D5379M-05
This test method covers the shear properties of composite materials reinforced by high-modulus fibers. The composite materials are limited to continuous-fiber or discontinuous-fiber-reinforced composites in specific forms.
2009
Event
Fundamentals of Adhesion (Peel) Testing
There is a reason people reach for Duct Tape as a fix for almost everything – Adhesion Strength. From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufactures.
2010
[Page extract]
BS EN ISO 13262
BS EN ISO 13262 is test method to determine the tensile strength of seams on thermoplastics spirally-formed structured-wall pipes.
2011
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2012
[Page extract]
BS EN ISO 22088-2
BS EN ISO 22088-2 is a test method for determining the environmental stress cracking of plastics.
This has replaced BS EN ISO 6252:1998
2013
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
2014
[Page extract]
ANSI/EIA 364
Mating and Unmating Procedure for Force Testing of Electrical Connectors and Sockets
2015
[Page extract]
BS ISO 6133
BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.
2016
[Page extract]
Belt/strap grips
Belt and strap grips - typically of a split-roller type in order to provide a rounded, smooth-surface around which a belt or strap can be looped several times.
2017
[Page extract]
Mors de serrage
Mors de serrage - composés de 2 mâchoires interchangeables ou fixes en forme triangulaire qui sont fixées dans un corps en métal.
2018
[Page extract]
CETIE Guide 9
This guide applies to the screw capping of pressurised wines & other beverages for narrow necks finishes with a redrawn metallic tamper-evident closure on a "BVS type" glass finish adapted for pressure caps. Includes sections on checking load setting on
2020
[Page extract]
ASTM D5179-16
ASTM D5179 is a test method for determining organic coatings adhesion to a plastic substrate. It can be used to evaluate the adhesion (pull-off strength) of various coating/substrate combinations e.g. paint and varnish.
2021
[Page extract]
ASTM C1341
This test method covers the determination of flexural properties of continuous fiber-reinforced ceramic composites in the form of rectangular bars formed directly or cut from sheets, plates, or molded shapes.
2022
[Page extract]
BS EN ISO 10591
This International Standard specifies a method for the determination of the influence of water on the adhesion cohesion properties of sealants with predominantly plastic behaviour which are used in joints in building construction.
2023
[Page extract]
ASTM D952-15
ASTM D952 is a test method that covers the determination of the bond strength or ply adhesion strength of sheet plastic and electrical insulating materials.
2024
[Page extract]
ASTM D3166
This test method covers the measurement of fatigue strength in shear by tension loading of adhesives on a standard specimen and under specified conditions of preparation, loading, and testing.
2025
[Page extract]
ASTM D7233-08
This test method covers a procedure for determining the number of fractures present when paintbrush filaments are bent.