Search results
1351
[Page extract]
Wedge grips
Wedge grips - consisting of 2 interchangeable or fixed jaws in the shape of a wedge which are secured in a metal body.
1352
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1353
[Page extract]
Three-point vs four-point bend testing
In a three-point bend test, force is applied at a single midpoint. In a four-point bend test, two loading noses distribute the load over a larger section of the specimen.
1354
[Page extract]
Why Mecmesin for compression testing
Mecmesin has a long history of providing reliable, standards-compliant compression testing systems to industries worldwide.
1355
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
1356
Event
Pull Force and Break Strength Testing
Whether it is medical tubing, plastic straws, copper wire or zip ties, pull force and break strength testing is critical not only to production quality but also to consumer safety.
1357
Test Frame
Helixa test frame
Helixa test frame
A precision motorised test frame designed to apply torque from a few mN.m right up to a capacity of 6 N.m. (50 lbf.in).Its sensitivity and axial alignment make it perfectly suited for testing fine-precision components in a quality…
1358
[Page extract]
How to conduct a grab test
A standard grab test involves the following steps:
1359
Event
Brütsch-Rüegger Tools at INNOTEQ 2025
Our trusted distributor, Brütsch-Rüegger Tools, will be exhibiting at INNOTEQ 2025 - the key event for Switzerland’s manufacturing industry.
1360
[Page extract]
Understanding compressive and tensile forces
Insertion and withdrawal testing focuses on two key force measurements:
1361
[Page extract]
Standards for tear resistance testing
While the core principle of wing tear testing remains the same, each standard specifies unique specimen shapes, notch sizes and test speeds. Adhering to these requirements ensures results are valid and comparable.
1362
[Page extract]
ASTM F1839-08
This specification covers rigid polyurethane foam blocks or sheets recommended for use as a standard material for mechanical testing using orthopedic devices and instruments.
1363
[Page extract]
ASTM C1292
This test method covers the determination of shear strength of continuous fiber-reinforced ceramic composites (CFCCs) at ambient temperature.
1364
[Page extract]
Speak to an expert
Selecting the right trapezoidal tear testing setup requires understanding both the material and the relevant standards.
1365
[Page extract]
What is lap shear testing under compression?
Lap shear testing under compressive load is a mechanical test used to determine the strength of
1366
[Page extract]
Coefficient of friction (COF) explained
Understanding the COF formula
The coefficient of friction (μ) is a dimensionless value calculated as:
1367
[Page extract]
Measurement and testing methods
Techniques for measuring tangent modulus
Tangent modulus is measured during tensile or compression testing, w
1368
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1369
[Page extract]
Introduction to Delft tear testing
The Delft tear test is a specialised method for determining the tear strength of vulcanised rubber, thermoplastic elastomers and similar flexible materials.
1370
[Page extract]
ASTM D1578
Significance and Use
Test Method D1578 for testing any spun yarn for breaking strength is considered satisfactory for acceptance testing of commercial shipments since the method has been used extensively in the trade.
1371
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1372
[Page extract]
Why is double lap shear testing important?
The double lap shear test is widely used to determine the performance of adhesives in structural and semi-structural applications. It allows engineers to:
1373
[Page extract]
BS ISO 11193-1
ISO 11193-1:2008 specifies requirements for packaged sterile, or bulked non-sterile, rubber gloves intended for use in medical examinations and diagnostic or therapeutic procedures to protect the patient and the user from cross-contamination.
1374
Product
Banc d'essais de force d'adhésion de reliure parfaite
Banc d'essai d'arrachage de page
802-001+853-415
Le banc d'essais d'arrachage de page Mecmesin 'Pira' est utilisé dans plus de 100 relieures à travers le monde .
Il fournit une méthode robuste, économique et répétable de mesure de la force d'arrachage des pages de livres à reliure…
1375
[Page extract]
Introduction to chord modulus
Chord modulus is a key parameter in material testing, providing engineers and quality control teams with a precise measure of a material’s stiffness under defined loading conditions.