Search results
1201
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
1202
[Page extract]
ASTM D3950
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.
1203
[Page extract]
ASTM D1708
ASTM D1708 is used to determine the tensile and elongation properties of small plastic microtensile specimens. These plastic specimens can be of any thickness up to 3.2 mm (1/8 in), including thin films. This test method does not require the use of an
1204
[Page extract]
ASTM D6049-03
This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular wei
1205
[Page extract]
ASTM D2731
ASTM D2731 is a test method for determining the elastic properties of elastomeric yarns made from rubber, spandex or other elastomers. Elastic properties include force at specified elongations, permanent deformation and stress decay.
1206
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
1207
[Page extract]
ISO 17454
ISO 17454 specifies a method for testing the adhesion between layers of multilayer pipes using a pulling test rig.
1208
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
1209
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
1210
[Page extract]
ISO 8067
ISO 8067 specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece
Method B, using an angle test piece without a nick
1211
[Page extract]
ASTM d6108-19
ASTM D6108 covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of straining or loading.
1212
[Page extract]
BS 6319-11
BS 6319-11 is a test method for determining creep in compression and in tension for resin and polymer/cement compositions used in construction
1213
[Page extract]
ASTM D695-15
ASTM D695 is a test method used to determine the mechanical properties of unreinforced and reinforced rigid plastics, including high-modulus composites, when loaded in compression at relatively low uniform rates of straining or loading.
1214
[Page extract]
SAE USCAR-21-4
This specification defines test methods and requirements for validation of solderless crimped connections.
1215
[Page extract]
ASTM F2878-10
This test method is used for determining the force required to cause a hypodermic needle to penetrate through protective clothing material.
1216
[Page extract]
BS EN 12814-3
BS EN 12814-3 is a tensile creep test method for testing welded joints of thermoplastics semi-finished products.
1217
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
1218
[Page extract]
ISO 11747
ISO 11747 specifies a method for the determination of resistance to extrusion of milled rice kernels, parboiled or not parboiled, after cooking under specified conditions.
1219
[Page extract]
BS EN 2747
BS EN 2747 is a tensile test method for testing carbon fibre reinforced plastics.
Before conducting BS EN 2747, it is important to read the entire specification. Standards can be obtained from appropriate standard authorities.
1220
[Page extract]
ASTM D4475-02
ASTM D4475 is a test method used for determining the horizontal shear strength of fiber reinforced plastic rods.
1221
[Page extract]
BS EN ISO 21181
BS EN ISO 21181 is a test method for determining the relaxed elastic modulus of light conveyor belts.
1222
[Page extract]
ISO 34-1
ISO 34-1 measures tear strength test methods for rubber test samples. The test results in measurement of a materials resistance to tearing. Tear strength can also be used to monitor material anisotropy of a material.
1223
[Page extract]
ASTM D3916
ASTM D3916 is a test method for determining the tensile properties of pultruded, glass-fiber-reinforced thermosetting plastic rod of diameters ranging from 3.2 mm to 25.4 mm.
1224
[Page extract]
BS EN ISO 376
BS EN ISO 376:2011 looks at the calibration of force-proving instruments used for the static verification of uniaxial testing equipment. These include tension and compression testing machines.
1225
Event
Compression Testing in Automotive Applications
From R&D to the shop floor, Compression Testing plays a key role in Automotive Manufacturing to meet strict quality controls and ensure consumer safety and product longevity.