Search results
951
[Page extract]
Standards for trapezoidal tear testing
Several international standards define this method, specifying specimen dimensions, slit length, and test speed. The most widely used include:
952
[Page extract]
Introduction to tension and compression testing
Tension and compression testing are among the most widely used mechanical testing methods for evaluating how a material or component performs under applied loads.
953
[Page extract]
Standards for flexural testing
Consistency in flexural strength testing is achieved through compliance with recognised standards, which define specimen dimensions, loading rates, and reporting requirements.
Key standards include:
954
[Page extract]
Understanding shear testing in tension
Shear testing in tension is a mechanical method used to measure the resistance of a material or bonded joint to forces acting parallel to the bonding surface.
956
[Page extract]
Test standards for compressive strength
The main recognised standards for ring crush testing are:
957
[Page extract]
Introduction to pull-off and pull-out testing
Pull-off and pull-out testing are widely used to measure the strength, durability, and reliability of materials, adhesives, coatings, and mechanical fixings.
958
[Page extract]
Key test standards
Grab method testing is governed by several internationally recognised standards, including:
959
[Page extract]
Test setup and equipment
Performing lap shear testing under compression requires careful alignment and use of appropriate fixtures to prevent torsion or uneven load distribution.
960
[Page extract]
Key standards
ASTM standards
ASTM D3470 - Procedures for measuring closure torque and assessing performance under applied stress
961
[Page extract]
Built for batch testing and automation
Batch testing in VectorPro uses a pre-configured test to create a semi-automatic or fully automatic testing system on sets of products and batches of the products.
962
[Page extract]
Understanding compressive properties
Compressive properties describe how a material responds to being pressed, squeezed or compacted.
963
Event
Automotive Component Torque Testing
This webinar will focus on the measurement of the torque resistance in knobs, switches, and torsion springs, which are among several components in automobiles that require testing to ensure quality, performance, and safety.
964
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.
965
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
966
Event
Webinar: Essentials of Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
967
[Page extract]
BS EN ISO 80369-7
This part of ISO 80369 specifies dimensions and requirements for the design and functional performance of small-bore connectors intended to be used for connections in intravascular applications or hypodermic connections in hypodermic applications of med
968
[Page extract]
ASTM D882-18
ASTM D882 is a test method that covers the determination of tensile properties of plastics in the form of thin sheeting and films (less than 1.0 mm (0.04 in.) in thickness). It is used to measure tensile properties including ultimate tensile
969
Event
WestPack Expo 2025
Lansmont - together with our sister brand Mecmesin - will be participating in the upcoming WestPack trade show!
970
Event
Tensile Testing: Extension, Elongation, Force & Failure
The primary objective for measuring and analyzing the the tensile force value of a product is to accurately determine one or more of these factors:
971
Product
Equipement pour tester des efforts physiques
Kit MHE dynamomètre à tester d'efforts ergonomiques
850-920
Le kit MHE de dynamomètre à tester d'efforts ergonomiques mesure les efforts de compression, de traction et de torsion afin d'évaluer l'impact ergonomique de tout type de force ou de couple de manutention manuelle.
Le kit complet comprend un berceau de…
972
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.
973
[Page extract]
BS 7907
BS 7907 gives recommendations for the design and manufacture of children’s clothing to promote mechanical safety. This standard is applicable to clothing intended for children up to 14 years of age.
975
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?