Search results
426
Accessory
Padded Radiused Probe, 500 N, 5-16 UNC
432-414
The Padded Radiused Probe is used with a short extension rod to connect to a digital force gauge to measure tension and compression.
It has a thin layer of rubber and is specially designed for use in manual handling and ergonomic assessment applications…
427
Accessory
Lower Torque Fixing Table, Vortex stands
432-320
Lower Torque Fixing Table.
Offers highly versatile holding of containers and specimens when torque testing. Fully adjustable between 10 - 190 mm opening (diameter) to accommodate a variety of forms.
Four rubber-coated, threaded pegs are supplied as…
428
Accessory
Wire Grip, 500 N, 10-32 UNF
432-397
The Wire Grip is designed for tensile testing up to 500 N of flexible thin wires, which may break easily when clamped.
The specimen is wrapped around a grooved 19 mm diameter bollard and the free end is clamped tightly in place using a pair of friction…
429
Accessory
1/2" Lower Chuck Assembly for use on Helixa motor spindle
432-616
A standard self-centering 3-jaw chuck with key. It has a maximum ½ " (12.7 mm) opening and is connected to the Helixa motor-drive spindle via an adaptor with quick-release grub-screw. Used to secure a variety of test specimens for torque applications of 1…
430
Accessory
Lightweight Pneumatic Plane Grip, Single-action, 200 N, pair, QC-20 fitting
Mec94
A pair of versatile Lightweight Pneumatic Plane Grips especially suitable for holding a variety of materials where the tensile force may be low but the material is sensitive to damage or slippage when clamped.
The adjustable screw-driven rod allows…
431
Accessory
Touchscreen Controller for OmniTest Materials Testers
432-846
The Touchscreen Controller has been designed for use with the OmniTest range of Materials Testers as an alternative to a desktop or laptop PC. It provides full PC capability, operating with an embedded version of Windows 10, specifically optimised for and…
432
Accessory
Pneumatic Medium Vice Grip - Double Action, 1 kN, 30 mm opening, pair, QC-20 fitting
Mec240k-S30+2Ko
MEC 240k- S30+2kO (body only) :
A pair of pneumatically-operated, Double-action Medium Vice Grips with an opening of 0-30mm depending on the jaw types selected (sold separately). Each grip is fitted with 2 x 50 mm diameter pneumatic pistons, which allow…
433
Accessory
Cone Probe, perspex, 45 degrees, M3
432-081
A perspex conical probe with 45° angle. Cone penetrometry is traditionally used within cosmetics and food products to assess hardness and spreadability. Also applicable for testing biscuits and other similar brittle products. Commonly used with extension…
434
Accessory
Compression Plate, Self-levelling, Hardened & Ground, 50 mm, 10-32 UNF
432-349
Self-levelling compression plates are ideal for general compression testing on a range of materials and finished products. Self-levelling allows parallelism to be set for those applications where it is critical to accurately measure the deformation of a…
435
Accessory
Pneumatic Medium Vice Grip - Single Action, 1 kN, 10 mm opening, pair, QC-20 fitting
Mec240k+Ko
MEC 240k +kO (body only) :
A pair of pneumatically-operated, Single-action Medium Vice Grips with an opening of 0-10mm depending on the jaw types selected (sold separately).
Each grip is fitted with 1 manual jaw holder + 1 x 50 mm diameter pneumatic…
436
Accessory
Peg Hook, 50 N, 10-32 UNF
432-399
The Peg Hook is fitted with 10-32 UNF female thread and supplied with a male grub-screw. It is designed for use in low-load applications where a small 'eyelet' needs to be held. The angled peg is ideal for quick and easy securing of the eyelet.
437
Accessory
Large Pneumatic Plane Grips, pyramid-faced jaws, 1 kN, Pair, QC-20 fitting
432-276
A pair of pneumatically-operated, single-action Large Pneumatic Plane Grips with an opening of 0-14 mm.
Each 30mm high x 51mm wide jaw is fitted with a pyramidal surface to secure specimens tightly. The specimen is held between the fixed jaw and the…
438
Accessory
Double Cam Grip (small serrated), 500 N, 10-32 UNF
432-387
The Small Double Cam Grip is designed for holding components into which the serrated faces can bite into the material and secure tightly eg. insulated cables and wire.
The specimen is secured between the 2 cams, which self-tighten as a load is applied…
439
Accessory
3/8" Upper Chuck Assembly for use on Helixa sensors
432-615
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
440
Accessory
Eccentric Roller Grip - Pyramid (serrated) roller, 5 kN, QC-20 fitting
Mec7-5
MEC7-5
Eccentric Cam Grip fitted with a pyramid-faced serrated 50mm wide roller cam. As a load is applied to a specimen the cam self-tightens , spreading the load evenly.
The lever allows for quick insertion and release of specimen to reduce testing…
441
Accessory
Pneumatic Medium Vice Grip - Single Action, 1 kN, 20 mm opening, pair, QC-20 fitting
Mec240k-S20+Ko
MEC 240k- S20+kO (body only) :
A pair of pneumatically-operated, single-action Medium Vice Grips with an opening of 0-20mm depending on the jaw types selected. Each grip is fitted with 1 manual jaw holder + 1 x 50 mm diameter pneumatic piston.
This…
442
Accessory
Lightweight Pneumatic Plane Grip, Single-action, 200 N, pair, QC-20 fitting
Mec94
A pair of versatile Lightweight Pneumatic Plane Grips especially suitable for holding a variety of materials where the tensile force may be low but the material is sensitive to damage or slippage when clamped.
The adjustable screw-driven rod allows…
443
Accessory
Lever-operated Cam Grip (large serrated), 500 N, 10-32 UNF
432-047
The Large Lever-operated Cam Grip is fitted with a 10-32 UNF female thread and supplied with a male grub-screw. It is designed with a plated 70mm wide roller cam to self-tighten as a load is applied to a sample, spreading the load evenly. The lever also…
444
Accessory
Custom-made Safety Guards and Enclosures
PDVguard
Where the standard safety guard does not fulfil your application requirements, Mecmesin can work with you to design and produce a custom-made safety guard to meet your exact requirements. Suitable for any Mecmesin test stand. Previously-designed guards…
445
Accessory
Sequin Pull-off Fixture, 50 N
432-291
The sample fabric is typically held in a separate 'grab test' textile fixture (432-323) mounted to the anvil plate. The sequin or other small appliqué is then clamped in the serrated jaw of a pair of 'Kelly' clamping forceps. This is then placed over a…
446
Accessory
Pneumatic Medium Vice Grip - Double Action, 1 kN, 10 mm opening, pair, QC-20 fitting
Mec240k+2Ko
MEC 240k +2kO (body only) :
A pair of pneumatically-operated, Double-action Medium Vice Grips with an opening of 0-10mm depending on the jaw types selected (sold separately).
Each grip is fitted with 2 x 50 mm diameter pneumatic pistons, which allow…
447
Accessory
Cable Cam Grip (small), serrated, 1 kN, 10-32 UNF
432-390
Cable Cam Grip - serrated, small
Designed for holding insulated cables and wire. The sample is secured by the cam, which self-tightens as a load is applied and spreads the load evenly.
Serrated cams are preferred for materials which may be slippy and…
448
Accessory
Webbing Grip, 2 kN, QC-20 fitting
432-269
Webbing Grips are designed for tensile testing of high strength belts and tapes below 2 kN.
The sample is wound around the knurled roller and then around the smooth roller. As load is applied, the smooth roller moves in the slot to secure tightly…
449
Accessory
Wedge Grip (small), 500 N, 10-32 UNF
432-385
The small, lightweight Wedge Grip is ideal for tensile testing below 500 N.
A spring-loaded lever ensures the serrated jaws (16mm wide x 20mm high) are easy to open for fast securing and release of samples. As load is applied, the self-tightening action…
450
Accessory
3/8" Lower Chuck Assembly for use on Helixa motor spindle
432-614
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5mm) opening and is connected to the Helixa motor-drive spindle via an adaptor with quick-release grub-screw.
Used to secure a variety of test specimens for torque applications.