Search results
576
Accessory
Square Perforated Aluminium Compression Plate, 150 x 150 mm, QC-20 or QC-32 fitting
Mec36L-150-L6x20
MEC36L-150-L6x20
Square Compression Plate in aluminium featuring perforations to allow air release during testing - suitable for foam testing. Holes are 6mm diameter and spaced at 20mm intervals.
Dimensions: 150mm x 150mm
Fitted with QC-20mm or 32mm…
577
Accessory
Dual Footswitches (non-locking type) for pneumatic grips
Mec205-1
Pneumatic grips are the ideal choice when performing tensile tests on sensitive materials that have a tendency to slip or break at point of clamping.
Mec205-1:
Non-locking dual footswitches open the jaws of the pneumatic grip by pressing the foot pedal…
578
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 100 mm
Mec240k-BG100
Rubber-faced Jaws (30mm x 100mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact…
579
Accessory
Dual Footswitches (non-locking type) for pneumatic grips
Mec205-1
Pneumatic grips are the ideal choice when performing tensile tests on sensitive materials that have a tendency to slip or break at point of clamping.
Mec205-1:
Non-locking dual footswitches open the jaws of the pneumatic grip by pressing the foot pedal…
580
Accessory
Charger for touchscreen digital gauges, Europe, USB-A, USB-C, 2-pin round
304-067
For use with Mecmesin touchscreen digital force and torque gauges. With 2 round pins. Commonly used in the Europe.
The mains adaptor/charger is a USB-A or USB-C type:
Input: 100-240V~50/60Hz 0.5A
Output-C: 5.0V=3.0A; 9.0V=2.22A; 12.0V=1.5A
Output-A: 3…
581
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 100 mm
Mec240k-BD100
Diamond Jaws (30mm x 100mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
582
Case study
Force d'extraction d'un briquet - Sécurité enfant
Exigence
Le client fabrique des briquets et développe actuellement u
583
[Page extract]
Introduction to compressibility and recovery testing
Compressibility and recovery testing measures how a material behaves under load and how effectively it returns to its original form once the load is removed.
584
Accessory
Charger for digital gauges, USA, 110 V/115 V, 2-pin flat
304-006
For use with Mecmesin digital force and torque gauges. 110 Volt with 2 flat pins. Commonly used in USA, Canada, Mexico and Japan.
The mains adaptor/charger is a constant-current type:
Primary circuit: 110V – 50-60Hz
Secondary circuit: 100mA constant…
585
Accessory
Upper Precision Fixing Plate for Helixa sensors
432-601
Precision Upper Fixing Plate for Helixa.
Mounts onto the square-drive of Helixa torque sensors. Fitted with a precision leadscrew and sprung-loaded runners into which jaws or holding pegs can be inserted (order separately). Tighten the knob to secure…
586
Accessory
90-degree Peel Jig for FPT-H1
432-620
This 90-degree Peel Jig fits to the FPT-H1 for 90 degree peel testing of pressure sensitive tapes and labels in accordance with international standards.
FINAT FTM2, ASTM D330. PSTC 101 Method F.
It accepts interchangeable float glass and stainless steel…
587
[Page extract]
Standards and guidelines
Accurate and comparable cleavage strength testing depends on following recognised international standards.
588
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-BG
Rubber-faced Jaws (30mm x 30mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
589
Accessory
Blank (smooth) Inset Jaws for MEC9 Thin Wire Grip, 2.5 kN
Mec9-EB
MEC9-EB Blank Jaws
Blank (smooth) inset jaws of 37 mm height x 15 mm width, 0.5 set. For fitting into the carrier of the MEC9 Thin Wire Grip.
Used when jaws require a specific surface to be machined onto them. Alternatively for affixing an abrasive…
590
Accessory
Charger for touchscreen digital gauges, Australia, USB-PD, 2-pin flat slant
304-060
For use with Mecmesin touchscreen digital force and torque gauges. With 2 flat slanted pins. Commonly used in the UK.
The mains adaptor/charger is a USB-A, USB-C type:
Input: 100-240V~50-60Hz 0.5A (USB-PD)
Output: 5VDC/3A or 9VDC/2.22A
591
Case study
Medical suture device calibration system
Requirement
A number of devices which 'crimp' a curved needle to a fine medical thread needed to be tested. The crimp force was applied horizontally pulling a lever on the device.
592
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 30 mm
Mec240k-BD
Diamond Jaws (30mm x 30mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
593
Accessory
Charger for digital gauges, UK, 230 V, 3-pin square
304-005
For use with Mecmesin digital force and torque gauges. 230 Volt with 3 square pins. Commonly used in the UK.
The mains adaptor/charger is a constant-current type:
Primary circuit: 230V – 50Hz
Secondary circuit: 100mA constant current at 9V Charger…
594
Accessory
Event-input cable for "switch-testing" on NEW(2011 - present) MultiTest/Vortex/Helixa-i and 'xt' stands
351-080
Event-Input Cable comprising 25-pin connector to split-connection fitted with a pair of 'crocodile clips'.
Allows a switch to be tested and the force/displacement/time to be identified when the switch closes or opens.
For use with the 'i' and 'xt'…
595
Accessory
Pyramid jaws for Mec11-20 Scissor Grip, 10 kN, 25 x 100 mm
Mec11-20-BP100
Pyramid Jaws (25mm high x 100mm wide) - nickel-plated having a surface of hardened steel pyramids of 1.2mm tall. By using 100 mm width jaws tensile force is reduced to 10kN.
For materials which need a “bite” to secure a good grip (e.g. soft metals {…
596
Accessory
1/2" upper chuck assembly for use on Helixa sensors (3 N.m & 6 N.m only)
432-617
A standard self-centering 3-jaw chuck with key.
It has a maximum ½" (12.7 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
597
Case study
Child safety - force to extract lighter
Requirement
The customer manufactures lighters and is currently developing a case/guard designed to increase the safety for children.
598
Accessory
Cable Cam grip for CrimpTest-1 kN
432-660
Cable Cam Grip for CrimpTest-1 Tester (supplied as standard with the Tester)
The Cable Cam Grip is designed for holding insulated cables and wire when tensile testing the pull strength of terminals up to 1 kN.
The cable is secured by the serrated cam,…
599
Accessory
Diamond coated jaws for Mec240k Medium Vice Grip, 30 x 80 mm
Mec240k-BD80
Diamond Jaws (30mm x 80mm) - nickel-plated having clamping surface coated with synthetic diamonds.
Opening span = see datasheet for various spans according to the grip body selected.
For materials which need a “bite” to secure a good grip (e.g. soft…
600
[Page extract]
ASTM F2193-02
These specifications and test methods provide standard specifications that specify material, labeling, and handling requirements for components used in surgical fixation of the spinal skeletal system such as metallic spinal screws, spinal plates, and sp