Search results
2476
[Page extract]
ISO 4587
Specifies a method for determining the tensile lap-shear strength of rigid-to-rigid bonded assemblies using a standard specimen under specified conditions of preparation and testing. This test procedure does not provide design information.
2477
[Page extract]
ASTM D6049-03
This test method is capable of measuring and characterizing the rheological behavior (viscosity and elasticity) of unvulcanized raw rubbers and rubber compounds, relating to the macro structure of rubber polymers (average molecular weight, molecular wei
2479
[Page extract]
ISO 11607-1
Specifies the requirements and test methods for materials, preformed sterile barrier systems, sterile barrier systems and packaging systems that are intended to maintain sterility of terminally sterilized medical devices until the point of use.
2480
Case study
Test de pelage à 90 degrés sur papier filtre
Exemple d'ingénierie sur mesure
Des accessoires à rouleaux flottants sont régulièrement utilisés pour tester les stratifiés lorsque la feuille de support est rigide et la feuille de face est flexible (par exemple, des cartes de sécurité).
2481
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
2483
[Page extract]
TAPPI T 456
TAPPI T456 is a test method that describes the procedure for the determination of the tensile strength of paper and paperboard after saturation with water.
2484
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
2485
Case study
Mandrins sur mesure pour bouchon de bouteilles
Exemple d'ingénierie sur mesure
Les bouchons en plastique appliqués sur les bouteilles peuvent être à paroi mince et flexibles, de sorte qu’ils se déforment lorsqu’ils sont saisis par un opérateur lors du test de couple.
2486
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
2487
[Page extract]
BS EN ISO 8670-2
Two part test on filled bags:
1) 20 N tensile flange seal test, pulled in two directions in turn, at 180 degrees, in shear plane across flange, bag held by transparent custom plate
2488
Case study
Essais sur mécanisme de lunettes ajustables
Exigence
Adlens fabrique des lentilles adaptatives utilisées sur des lunettes distribuées dans le monde entier. Les lentilles changent de puissance en tournant le cadran situé sur le côté de la paire de lunette.
2489
[Page extract]
TAPPI T 838
This method describes a procedure for determining the edgewise compressive strength, parallel to the flutes, of a short column of singe, double, or triple-wall corrugated fiberboard, in a neckdown, non reinforced, loading edge configuration.
2490
Event
Fundamentals of Cork Pull & Elasticity Testing
Natural corks need to execute several important functions within the champagne and wine industries in order to meet consumers’ expectations and also to guarantee the quality of the drink.
2491
[Page extract]
PSTC 8
Unwind adhesion is a quantitative measure of the degree of ease or difficulty in unwinding a roll of tape.
The test specimen shall be any 10 m (10 yard) or more roll of pressure sensitive tape - preferably 24 mm (1”) wide.
2492
Page
Missing link
The page you requested wasn't found on this site. It could have moved or something has gone wrong.
2493
Specials
Touchscreen Controller VectorPro
Touchscreen Controller
The Touchscreen Controller has been designed for use with the Twin-column OmniTest range of Materials Testers as an alternative to a desktop or laptop PC.
2494
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2495
[Page extract]
BS EN 1155
Closing and check mechanisms, Door closers, Electrically-operated devices, Ironmongery (buildings), Classification systems, Design, Performance, Durability, Temperature-rise limit, Test equipment, Sampling methods, Performance testing, Temperature, Elec
2496
[Page extract]
BS EN ISO 8339
This International Standard specifies a method for the determination of the tensile properties of sealants used in joints in building construction.
2497
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
2498
[Page extract]
BS ISO 2285
BS ISO 2285 is a test method for determining the tension set under constant elongation of vulcanised rubber or thermoplastic.
2499
[Page extract]
BS EN ISO 19011:2011
Provides the fundamental knowledge needed for auditing management systems and has been expanded to reflect modern thinking and the intricacies of auditing multiple management system standards (MSS).