Search results
1201
[Page extract]
Procedure for tensile testing
While the specifics vary depending on material type and applicable standards, the general procedure includes:
1202
[Page extract]
Understanding shear testing in tension
Shear testing in tension is a mechanical method used to measure the resistance of a material or bonded joint to forces acting parallel to the bonding surface.
1203
[Page extract]
Wines & Spirits
Wine incites passion and has stirred the emotions for centuries. It demands attention. But it’s not just the wine itself which get us talking, it’s how it is packaged too; bottles and corks, bag-in-box containers, aseptic cartons and cans.
1204
[Page extract]
Pharmaceuticals
The pharmaceutical industry is tightly controlled and subject to strict regulations, which means that testing is often at the heart of demonstrating compliance to the various international standards which govern the industry.
1205
[Page extract]
BS ISO 6133
BS ISO 6133 specifies five methods of calculating, after testing, the tear strength and the adhesion strength of vulcanized rubber or fabrics coated with or adhered to rubber or plastics.
1206
[Page extract]
ASTM D5868-01
Due to the increased use of adhesively-bonded FRP as a result of the inherent advantages afforded by bonded rather than mechanically-fastened joints (particularly the alleviation of stress risers and stress cracking), there is a need for tests by which
1207
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1208
Case study
Système d'essai de force de traction sur filet d'échafaudage
Exigence
Huck, un fournisseur de filets d'échafaudage, organise un retour chez le fabricant pour vérifier que les filets ne se sont pas dégradés pendant leur utilisation.
1209
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
1210
[Page extract]
ISO 6383-1
ISO 6383-1 specifies a method of determining the tear resistance of plastic film or sheet less than 1 mm thick, in the form of standard trouser-shaped test specimens, tested under defined conditions of pre-treatment, temperature, humidity, and speed of
1211
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
1212
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1213
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1214
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
1215
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
1217
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1218
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
1219
Case study
Essais sur bouteilles PET
Exigence
Esterform Packaging fabrique plus d'un million de bouteilles et préformes en PET par jour pour les principaux fournisseurs d'eau en bouteille, de jus de fruits, de boissons non alcoolisées, de produits laitiers et de produits mén
1220
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1221
[Page extract]
ASTM F3014-14
1.1 This test method describes the procedure for penetration testing sharp and blunt needles used for the placement of surgical sutures. It only describes the test procedures (Phase 1) and does not define a test medium at this time.
1222
Event
Fundamentals of Food Texture Testing and Analysis
Texture cannot be controlled unless it measured in a consistent and repeatable manner.
1223
Case study
Luer lock fastening and release torque
Customised engineering example
Luer lock test standards frequently call for measuring torque whilst simultaneously applying a pre-defined axial force.
1224
[Page extract]
BS EN ISO 19011:2011
Provides the fundamental knowledge needed for auditing management systems and has been expanded to reflect modern thinking and the intricacies of auditing multiple management system standards (MSS).
1225
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.