Search results
2101
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2102
[Page extract]
Consumer Products
Mecmesin test solutions for products typically found in the home ...
2103
[Page extract]
Step-by-step guide to conducting a CMT test
Prepare the specimen - Cut to size with clean edges, ensuring flutes remain undamaged, and condition as per the standard.
Calibrate the equipment - Check the load cell and platen alignment.
2104
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2105
[Page extract]
ASTM C297
This test method determines the flatwise tensile strength of the core, the core-to-facing bond, or the facing of an assembled sandwich panel.
2106
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
2107
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
2108
[Page extract]
ASTM C961
This test method covers a laboratory procedure for determining the lap shear strength of sealants. It also provides information on the adhesive bond of the sealants to the tested substrates.
2109
[Page extract]
ASTM D6195-03
These test methods cover the determination of properties of a pressure-sensitive adhesive. These test methods are applicable to those adhesives that form a bond of measurable strength rapidly upon contact with another surface.
2111
[Page extract]
Challenges and best practices in peel testing
Common challenges
Material variability in thickness, surface treatment, or adhesive application.
Inconsistent specimen preparation.
Operator error from misalignment or incorrect grip tension.
Best pra
2112
[Page extract]
IEC 60371-2
Part 1 is definitions of general requirements
Part 3 specifications for individual materials
A number of other non-force/torque properties are tested. This is largely about testing of pressure-bonded laminated materials.
2113
[Page extract]
ASTM D5766 / D5766-M
ASTM D5766 is a test method to determine the open-hole tensile strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibres.
2114
[Page extract]
ISO 12236
Specifies a method for the determination of the puncture resistance by measuring the force required to push a flat-ended plunger through geosynthetics.
2115
Caso de estudio
Validación de par de cierre
Requisito El cliente tenía varios probadores de par de cierre Tornado y deseaba realizar verificaciones de validación periódicas sin la necesidad de devolver las unidades a Mecmesin o a un laboratorio aprobado.
2116
[Page extract]
BS EN 1465
Specifies a method for determining the tensile lap-shear strength of bonded assemblies when tested on a standard specimen and under specified conditions of preparation and testing.
2117
[Page extract]
SAE J174M
This test procedure is intended to provide a quality control method for checking torque-tension characteristics of non-prevailing torque type threaded steel fasteners 6 through 24 mm nominal diameters.
2118
[Page extract]
BS EN 50289-3-17
Communication cables, Electric cables, Communication transmission lines, Mechanical testing, Adhesion tests, Dielectric materials, Cable sheaths
2119
[Page extract]
BS 2782-12: 1210A to C
BS 2782-12: Method 1210A to C specifies a test method for testing the longitudinal tensile properties of glass-reinforced thermosetting plastics (GRP) pipes.
2120
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
2121
[Page extract]
BS EN 12814-1
BS EN 12814-1 is a bend test method for testing welded joints of thermoplastics semi-finished products.
2122
Caso de estudio
Prueba de resistencia de extracción de página
Requisito Mecmesin colaboró con un cliente para diseñar y desarrollar un sistema de medición de fuerza para determinar la fuerza adhesiva de encuadernación de libros en la retención de páginas individuales.
2123
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
2124
[Page extract]
ISO 8627
Specification of a test method and grading scheme for the stiffness of the tufted area of conventional manual tooth-brushes, together with the relevant information concerning definitions and those concerning testing machines.
2125
[Page extract]
SAE J 1907
This recommended practice defines a procedure for the construction and testing of a 180 deg peel specimen for the purpose of determining the bondability of glass to elastomeric material in automotive modular glass.