Search results
1726
Event
Advanced Engineering 2021 - We would love to see you there!
Who should attend?
Engineering professionals and managers from advanced manufacturing sectors interested in quality assurance testing solutions.
What is the exhibition about?
1727
[Page extract]
Step-by-step procedure for reverse ratchet torque testing
Sample preparation
Condition the closures according to the specified standard to control environmental factors.
1729
[Page extract]
ASTM D3106
This test method covers the determination of the permanent deformation of bare, continuous elastomeric monofilaments and filament yarns made from rubber, spandex, anidex, or other elastomers subjected to prolonged periods of tension.
1730
[Page extract]
ISO 7886-3
This document specifies the properties and performance of sterile single-use hypodermic syringes with an auto-disable syringe feature intended to deliver a fixed dose of vaccine immediately after filling.
1731
Event
Wine & Spirits Capping: Cork Pull & Twist Caps
Wine packaging has a great influence on the quality of the product delivered to the customer.
1732
Caso de estudio
Break-loose and sustaining force tests of pre-filled drug cartridges to ISO 11608-3
Requirement
Mechanical pen injectors for delivering drugs, such as insulin, have found increasing acceptance over the traditional vial-and-syringe method. Advances in pen design have made models increasingly user-friendly, allowing superior ac
1733
[Page extract]
ASTM d6108-19
ASTM D6108 covers the determination of the mechanical properties of plastic lumber and shapes, when the entire cross-section is loaded in compression at relatively low uniform rates of straining or loading.
1734
Caso de estudio
Par de extracción de la tapa del catéter
Ejemplo de ingeniería personalizada Nuestro cliente estaba probando el par de liberación de las tapas de catéter de plástico de 20 mm de largo con características irregulares para ayudar a agarrar los dedos.
1735
Caso de estudio
Jeringa de vidrio Luer lock accesorio extraíble
Ejemplo de ingeniería personalizada Los adaptadores Luer Lock de policarbonato se ajustan a presión a las boquillas de jeringa de vidrio con un ajuste por fricción.
1736
[Page extract]
ASTM D2344 / D2344M
ASTM D2344 is a test method, which determines the short-beam strength of high-modulus fiber-reinforced composite materials. It is applicable to all types of parallel fiber reinforced plastics and composites.
1737
[Page extract]
ASTM E1820-18ae1
The ASTM E1820 test method covers procedures and guidelines for the determination of fracture toughness of metallic materials using the following parameters: K, J, and CTOD (δ). Toughness can be measured in the R-curve format or as a point value.
1738
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1739
[Page extract]
ASTM D378
The ASTM D378 test method is used for evaluating the physical properties of flat conveyor belting, which are used in many industrial applications in which they are subjected to a great variety of stresses and conditions.
1740
[Page extract]
Procedimiento de ensayo
La realización de la prueba de penetración y arrastre de la aguja implica varios pasos:
1741
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1742
[Page extract]
BS EN 12814-4
BS EN 12814-4 is a peel test method for testing welded joints of thermoplastics semi-finished products.
1743
[Page extract]
ASTM D575-91
These test methods cover two test procedures for determining the compression-deflection characteristics of rubber compounds other than those usually classified as hard rubber and sponge rubber.
1744
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
1745
[Page extract]
BS EN 12242
The BS EN 12242 test method is used to determine the peel strength of a touch and close (also known as “hook and loop”) fastener through a 180° peel test that is able to determine average peel and the peel strength characteristics of the product for a g
1746
Caso de estudio
Esfuerzo de torneado del enrollador de ventanas automotrices
Requisito El cliente solicitó un sistema portátil que le permitiera probar rápida y fácilmente el torque requerido para abrir y cerrar ventanas en un automóvil.
1747
Caso de estudio
Injection moulded assembly integrity
Customised engineering example
Plastic injection-moulded subassemblies are often clipped or welded together, and the integrity of the whole must be tested at several points.
1748
[Page extract]
ISO 9664
The principle of the method specified is cyclically stressing the specimen in a way that may be regarded as the superposition of an alternating stress on a static stress which is the mean stress.
1749
[Page extract]
ASTM D1621
ASTM D1621 is used to measure the compressive properties of rigid cellular materials, particularly expanded plastics. Calculations include compressive strength, compressive strain, compressive stress and compressive modulus.
1750
Sensor
Sensors - MultiTest-dV
Force sensors
The MultiTest-dV is a highly flexible tester, which can be configured with either a Touchscreen or Advanced Force Gauge for product testing or an Enhanced Load Sensor for basic materials testing.
AFGA digital force gauge with advanced…