Search results
926
Caso de estudio
Physiological measurement of joint strength
Requirement
The La Trobe University in Melbourne required a device to test the first Metatarsophalangeal joint, commonly known as the big toe. They wanted to compare different patients toe strength.
927
Event
Compressive Crush Force Testing
This webinar will focus on identifying and troubleshooting variables that impact compressive force testing, setting up repeatable compression force tests and establishing consistent testing standards for your products.
928
Caso de estudio
Medical suture device calibration system
Requirement
A number of devices which 'crimp' a curved needle to a fine medical thread needed to be tested. The crimp force was applied horizontally pulling a lever on the device.
929
Caso de estudio
Peel test of semi-rigid packaging for medical device
Customised engineering example
Our client needed to test the peeling quality of a Tyvek® paper lid used to seal a sterile, semi-rigid thermoformed plastic tray containing pre-filled syringes.
930
[Page extract]
TAPPI T 400
This method describes procedures for obtaining a representative sample for testing.
931
Caso de estudio
Electrical connector insertion and withdrawal forces
Customised engineering example
Push-fit electrical connectors with hole or dimple detents (also known as 'spade terminals') must offer a firm but practical fit.
932
Caso de estudio
Prueba de aplastamiento de bandejas de comida rápida
Requisito Como proveedor de bandejas de comida rápida, el cliente necesitaba asegurarse de que las bandejas resistirían una cierta fuerza lateral sin daños para asegurarse de que no se rompieran al ser manipuladas y cargadas con alimentos.
933
[Page extract]
ASTM D624-00
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
934
Caso de estudio
Diamante pull-off test
Requirement
The customer was a supplier to major UK clothing retailer Marks & Spencer, who stipulate that all fasteners and attachments must be tested to failure.
935
Caso de estudio
Prueba de extracción del filtro respiratorio en línea
Ejemplo de ingeniería personalizada Un fabricante de productos de filtración necesitaba probar la fuerza de extracción de un filtro respiratorio cuando se extraía de un dispositivo médico en línea.
936
Caso de estudio
Cierres de líquidos a granel
Ejemplo de ingeniería personalizada Nuestro cliente fabrica transportadores de líquidos a granel equipados con cierres de válvulas de plástico de dos partes.
937
Caso de estudio
Prueba de botones del tablero
Requisito Visteon requirió un sistema automatizado para medir la fuerza de actuación de los botones del tablero y verificar los puntos de cierre del contacto eléctrico.
938
[Page extract]
ASTM C165
1.1 This test method covers two procedures for determining the compressive resistance of thermal insulations.
939
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
940
[Page extract]
ASTM F2132-01
This specification provides the performance requirements and associated test procedures for the puncture resistance of materials used in the construction of containers for discarded medical needles and other sharps.
941
Caso de estudio
Insulation film stiffness testing
Customised engineering example
Familiar with three-point bending to test flexural strength properties?
942
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
943
Caso de estudio
Torsion spring testing
Customised engineering example
Unlike most compression and tension springs, torsion springs are produced in a variety of forms with differing leg positions.
944
Caso de estudio
Closure torque validation
Requirement
The customer had a number of Tornado closure torque testers, and wished to carry out regular validation checks without the need to return the units to either Mecmesin or an approved laboratory.
945
Caso de estudio
Integridad de la bolsa de té
Ejemplo de ingeniería personalizada Algunas de las aplicaciones más simples pueden no parecer tan obvias cuando las enfrentas. ¿Una cuerda y una lengüeta en una bolsita de té?
946
Caso de estudio
Tensile test on footwear materials
Requirement
William Lamb Footwear is one of the UK's leading footwear distributors. A test system was required to measure and ensure that the footwear and its components passed quality standards set out by their end-customers.
947
Caso de estudio
Press stud popper pull-off test
Requirement
The customer was a supplier to major clothing retailer Marks & Spencer, who stipulate that all fasteners and attachments must be tested to failure.
948
Caso de estudio
Box crush test (BCT) and transit packaging compression testing
Customised engineering example
Boxes for the consumer and transit packaging industries must be as light as possible whilst still retaining a robustness to contain and protect their contents and also have the strength to stand up to shipping, ha
949
[Page extract]
Force systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers?
950
Caso de estudio
Torque tester for a range of tamper-evident caps
Requirement
Elopak required equipment for the manual testing of tamper-proof seals on bottle caps, but without the bottle being present. The unit had to accommodate a range of different size caps.