Search results
2076
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
2077
Producto
Probadores de impacto de dardos que caen
Gama MEC-FD
MEC-FD1
La gama Mecmesin MEC-FD Falling Dart Impact Tester está diseñada para medir la resistencia al impacto o la tenacidad de las películas de plástico de conformidad con los métodos A y B de dardos de caída libre ASTM D1709 e ISO 77
2078
Producto
Calibrador de llave dinamométrica
TWC
875-001
El Calibrador de Llave de Torsión TWC es una solución simple y rentable para verificar las configuraciones en llaves estándar de 'haz', 'clic' y 'ruptura'. Operado manualmente y midiendo el torque en sentido horario y antihorario…
2079
[Page extract]
BS 6319-7
BS 6319-7 is a test method for determining the tensile strength of resin and polymer/cement compositions for use in construction.
2080
[Page extract]
ASTM D3577
1. Scope ... 1.1 This specification describes certain requirements for packaged sterile rubber surgical gloves used in conducting surgical procedures.
2081
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
2082
[Page extract]
BS EN ISO 11857
Textile floor coverings, Floor coverings, Sheet flooring, Mechanical testing, Textile testing, Textiles, Tensile testing, Test equipment, Test specimens, Testing conditions.
2083
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
2084
[Page extract]
CETIE Guide 5
This document gives background information and recommended best practices for the application of plastic flat-top screw-on caps onto PET bottles for beverages. It covers all closure sizes and beverage product types.
2085
[Page extract]
ASTM F2332-06
This specification covers annular ball bearings intended primarily for use in instrument and precision rotating components.
2086
[Page extract]
SAE AIR 1471A
The purpose of this SAE Aerospace Information Report (AIR) is to provide the aerospace propulsion industry with recommended assembly torque limits for commonly used aircraft propulsion system threaded fasteners when a common torque value per fastener si
2087
[Page extract]
ISO 20126
This International Standard specifies requirements and test methods for the physical properties of manual toothbrushes in order to promote the safety of these products for their intended use.It does not apply to manual interdental brushes and powered or
2088
[Page extract]
ASTM D1004
ASTM D1004-13 covers the determination of tear strength or tear resistance of flexible plastic film and sheeting. The site of tear is initiated by a high stress concentration caused by the 90° angle in the specimen.
2089
[Page extract]
BS EN 681-1
This standard specifies requirements for materials used in vulcanized rubber seals for:
1) cold potable water supply (up to 50®C);
2090
[Page extract]
BS EN ISO 10555-3
Catheters, Cannulas, Sterile equipment, Parenteral infusion equipment, Medical equipment, Medical instruments, Disposable, Marking, Flow rates, Force, Force measurement, Flow measurement, Test equipment, Testing conditions.
2091
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
2092
[Page extract]
PSTC 101
These methods cover the measurement of the peel adhesion of pressure sensitive tapes.
2093
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
2094
Event
Fundamentals of Food Texture Testing and Analysis
Texture cannot be controlled unless it measured in a consistent and repeatable manner.
2095
Producto
Probador de par motorizado
Vortex-dV
876-601
El Vortex-dV es un probador de par autónomo, versátil, robusto y de 10 Nm . Fácil de usar, es adecuado para controles de calidad de rutina en un entorno de producción o laboratorio. Configure este soporte accionado por motor con un sensor de torque…
2096
[Page extract]
ISO 604
ISO 604 specifies a method for determining the compressive properties of plastics in the form of standard test specimens when tested under defined conditions of pretreatment, temperature, humidity and testing machine speed.
2097
[Page extract]
ASTM D4476 / D4476M-14
ASTM D4476 is a test method used to determine the flexural properties of fiber-reinforced pultruded plastic rods. The specimen used is a rod with a semi-circular cross section, moulded or cut from lengths of pultruded rods.
2099
[Page extract]
ASTM D6112-18
ASTM D6112 cover the determination of the creep and creep-rupture properties of plastic lumber and shapes, when loaded in compression or flexure under specified environmental conditions. Test specimens in the “as-manufactured” form are employed.