Search results
1151
[Page extract]
FAQs about Young's modulus testing
What is the difference between Young’s modulus and tensile strength?
Young’s modulus measures stiffness - how much a material deforms under stress.
1152
[Page extract]
Step-by-step needle penetration testing process
Sample preparation
Specimens are cut to the required dimensions and conditioned to the specified environmental parameters such as temperature and humidity. Thickness and surface finish are controlled for consistency.
1153
[Page extract]
Introduction to secant modulus
In material testing and engineering, understanding how a material responds to applied stress is essential for predicting performance, ensuring safety, and optimising design.
1154
[Page extract]
Applications across sectors
Texture testing in food manufacturing
Bread softness for freshness control, snack crispness for quality assurance, firmness in
1155
[Page extract]
Torque testing standards
A range of recognised standards define the correct procedures for reverse ratchet torque testing, ensuring consistent and reliable results.
1156
[Page extract]
What is fastening torque
Fastening torque refers to the rotational force applied to tighten a fastener, typically measured in Newton-metres (N·m) or pound-force inches (lbf·in). The correct torque value ensures adequate clamping without overstressing components.
1157
[Page extract]
Types of compressive shear tests
Test configurations vary according to the material, application, and relevant industry standard.
1158
[Page extract]
How peel wheel tests are conducted
Specimen preparation – The bonded material is cut to defined dimensions, ensuring uniformity of size and adhesive application.
1159
[Page extract]
Relevant textile test standards
The strip method is defined in several national and international standards, each tailored to specific fabric types and performance requirements:
1160
[Page extract]
Introduction to friction in material science
Friction is a critical factor in how materials behave under movement. It is the resistive force that occurs when two surfaces are in contact and attempt to slide against each other.
1161
[Page extract]
Standards and compliance
International standards ensure penetration and puncture testing is performed consistently for reliable and comparable results.
Key examples include:
1162
[Page extract]
Step-by-step test methodology
Preparation
Sample selection - Choose representative specimens, avoiding faults unless deliberately testing them.
Specimen cutting - Cut to standard dimensions with a central slit of specified
1163
[Page extract]
Magnets and solenoids
Solenoids, a type of electromagnet generating a uniform magnetic field when an electric current is passed through it, have applications in many different types of industries.
1164
[Page extract]
Introduction to the ring crush test
The ring crush test (RCT) is a key method for determining the edgewise compression strength of paper and paperboard.
1165
[Page extract]
Types of flexure tests
Different flexure testing setups are chosen based on the nature of the material, the required precision, and the industry standards being followed.
1166
[Page extract]
How running torque is measured
Running torque is typically measured using precision torque sensors mounted within a controlled test stand. The component under test is rotated at a defined speed, and torque is measured continuously during motion.
1167
[Page extract]
Yield point testing methods
Yield point testing is most often performed using tensile testing, in which a specimen is subjected to a steadily increasing axial load until plastic deformation occurs.
1168
[Page extract]
Test setup and equipment
Performing lap shear testing under compression requires careful alignment and use of appropriate fixtures to prevent torsion or uneven load distribution.
1169
[Page extract]
Understanding cone penetration testing
Cone penetration testing is a precision method used to determine a material's resistance to penetration by a standardised cone-shaped probe under specific force conditions.
1170
[Page extract]
Understanding tear strength and its importance
Tear strength measures the force a material can withstand before a tear propagates. It covers both the initial rupture and the resistance to further tearing once damage has started.
1171
[Page extract]
Interpreting breakaway test results
Understanding test outputs is as crucial as conducting the tests themselves.
Slip torque vs bridge torque
Slip torque reflects the resistance encountered before rotation begins—a measure of seal integrity and usability.
1172
[Page extract]
Standards and compliance
ASTM D2063 defines methods for determining application and r
1173
[Page extract]
Understanding ASTM D2718 standards
The ASTM D2718 standard sets out the procedures for conducting planar shear tests on structural panels using the
1174
[Page extract]
Understanding reverse ratchet torque
Reverse ratchet torque testing is an essential process for verifying the safety and reliability of child-resistant closures (CRCs).
1175
[Page extract]
Introduction to flexural testing
Flexural testing is a core method in materials science, used to evaluate how materials perform when subjected to bending stresses.