Search results
2751
[Page extract]
ASTM D1000
These test methods cover procedures for testing pressure-sensitive adhesive-coated tapes to be used as electrical insulation. These tapes are classified as follows:
Class 1—Non-elastomeric backings made from materials
2752
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
2753
[Page extract]
EN 16287
Series of standards, including 16288, 16289, 16290, 16291, 16292, 16293 and others
Dimensions and specifications for a series of bottle finishes, including corks, crown, screw threads, including bottles with internal pressure.
2754
[Page extract]
ASTM D3044
This test method covers determination of the shear modulus of wood-based structural panels associated with shear distortion in the plane of the panels. The method is applicable to all types of wood-based structural panels.
2755
[Page extract]
ISO 12625-4
Specifies a test method for the determination of the tensile strength, stretch at break and tensile energy absorption of tissue paper and tissue products. It uses a tensile-testing apparatus operating with a constant rate of elongation.
2756
Event
Tensile Testing: Basics, Tips and Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2757
[Page extract]
BS 4839
Specification for Blow moulded polyolefin containers, part 2: Plastics containers. Containers over 5 litres and up to 60 litres capacity
2758
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
2759
[Page extract]
ISO 2409
Describes a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate.
2760
[Page extract]
ASTM F1140/F1140M-13
These test methods provide a rapid means of evaluating tendencies for package failure when the package is exposed to a pressure differential. Pressure differentials may occur during processes such as sterilization and transportation.
2761
[Page extract]
*corp QPF-MC-1209 B
*Strictly confidential*
L'Oreal to methods for shear and penetration testing of lipsticks, deodorants etc.
2762
[Page extract]
ASTM D3474
This standard covers the calibration and use of torque meters of the type normally used in packaging applications.
2763
[Page extract]
TAPPI T 576
This test method decribes the procedure, using constant-rate-of-elongation, for determining three tensile breaking properties of towel and tissue: tensile strength, stretch, and tensi;e energy absorption.
2764
[Page extract]
BS EN 12467
Sheet materials, Asbestos cement, Cements, Fibres, Reinforced materials, Sheet roof coverings, Cladding (buildings), Curtain walling, Grades (quality), Density, Strength of materials, Approval testing, Type testing, Quality control, Acceptance inspectio
2765
[Page extract]
TAPPI T 841
This method describes procedures for determining the edgewise compressive strength, parallel to the flutes, of a short column of single wall and double wall corrugated fiberboard.
2766
[Page extract]
CETIE Guide 7 (FR)
Ce guide concerne le bouchage à vis des vins tranquilles, avec une fermeture métallique avec insert plastique fileté et témoin de violabilité ou bande de garantie qui doit être déchiré à l’ouverture.
2767
[Page extract]
ASTM D1600
ASTM D1600 is a source of reference for definitions of abbreviated technical terms used in the plastics industry
Standards can be obtained from appropriate standard authorities.
2768
[Page extract]
BS EN ISO 22254
ISO 22254:2005 specifies a test method for determining the resistance of the tufted portion of manual toothbrushes to deflection. This could be used to derive a stiffness - a factor which has been of great concern to consumers and manufacturers.
2769
[Page extract]
USP 1207.3
USP 1207.3 provides guidance on the integrity assurance of nonporous packages intended for sterile pharmaceutical products. Background instruction is provided on the topics of leaks, leakage rate, and package sealing/closure mechanisms
2770
[Page extract]
ASTM C364
This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.
2771
[Page extract]
SAE AS1310B
This SAE Aerospace Standard (AS) is intended for use by those involved in the design of aircraft, missile, or space systems, and their support equipment to define the various type of fastener torque.
2772
Event
Tensile Testing: Basics, Tips, & Trends
Have you ever wondered if the seatbelt in your vehicle is strong enough to restrain you in a collision? How about the average person pulling the cork out of a wine bottle?
2773
[Page extract]
DIN 6094
Dimensions and specifications for a series of bottle finishes, including corks, crown, screw threads, including bottles with internal pressure.
2774
[Page extract]
ASTM D5656-10
This test method covers the preparation and testing of thick-adherend lap-shear samples for the determination of the stress-strain behavior of adhesives.
2775
[Page extract]
IEC 60512-13-1
Details a standard test method to measure the force to fully engage or separate mating connectors, including the effect of any locking, latching, sealing, engaging, separating or similar device, that assists or resists such operation.