Search results
1126
[Page extract]
BS ISO 11752
BS ISO 11752 is a test method for determining the compressibility of flexible cellular polymeric materials.
1128
Caso de estudio
Headset microphone joint torque
Requirement
Jabra is a subsidiary of GN Netcom and is a global manufacturer of innovative headsets (wireless and corded) and speakerphone solutions.
1129
[Page extract]
BS 7320
This British Standard specifies requirements for sharps containers intended to hold potentially infectious medical waste comprised largely of devices which can readily cause physical injury e.g. scalpel blades, hypodermic needles and syringes.
1130
[Page extract]
CETIE Guide 1
This guideline applies to the capping of still wines with a cork mouth finish as per CETIE data sheet GME 50.01 which has been used as a base for the European standard EN 12726. Contains reference to 'extraction force', 'cork dimensional recovery', 'ch
1131
Caso de estudio
Top-load testing PET bottles
Requirement
Esterform Packaging manufacture more than a million PET bottles and preforms per day for major processors of bottled water, juices, soft drinks, dairy and household products.
1132
[Page extract]
ASTM D3410 / D3410M
ASTM D3410 determines the compressive properties of polymer matrix composite materials reinforced by high-modulus fibers.
1133
Caso de estudio
Synthetic sports surface tuft binding
Customised engineering example
Test method standard BS ISO 4919 applies to the tuft withdrawal force of carpets.
1134
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
1135
[Page extract]
ASTM D4776 / D4776M-18
ASTM D4776 is a test method used to determine the maximum adhesion force of tyre cords in rubber compounds.
1136
Caso de estudio
Medical sharps bin puncture resistance
Customised engineering example
International standards (ASTM F2132, BS 7320, BS 23907) specify the puncture resistance of medical sharps containers.
1137
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
1138
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
1139
Caso de estudio
Grenade cartridge sheath projectile separation pull testing
Requirement
When manufacturing ammunition, the projectile is set into the case and it is crimped or sealed in place.
1140
Sensor
Sensors - Helixa
Torque sensors
The HTC range of interchangeable torque sensors are specially adapted for the Helixa test system. Plug and play for automatic calibration with availability to suit all requirements in capacities from 0.1 N.m (0.9 lbf.in) to 6 N.m (50 lbf.in…
1141
[Page extract]
UL 486A-B
UL 486A-B is a safety standard that outlines the requirements for wire connectors and soldering lugs used with electrical conductors.
1142
Página
Enlace perdido
La página que solicitó no se encontró en este sitio. Podría haberse movido o algo salió mal.
1143
[Page extract]
ASTM D3469
These test methods measure the downward forces during the disengagement of lug-style caps from their respective containers. The methods measure the maximum torque developed while the cap is further disengaged by turning of the container.
1144
[Page extract]
ASTM D6068-10
This test method covers the determination of the J-integral versus crack growth resistance (J-R) curves for polymeric materials.
1145
[Page extract]
ASTM D413-98
ASTM D413 is a test method used to determine the force per unit width required to separate a rubber layer from a flexible substrate such as fabric, wire or sheet metal.
1146
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
1147
[Page extract]
ISO 8113
ISO 8113 specifies a method for determination of the resistance of glass containers to external force in the direction of the vertical axis.
1148
[Page extract]
ASTM D3950
This specification covers nonmetallic strapping and joining methods for closing, reinforcing, and bundling materials for shipment, unitizing, palletizing, and bracing for car and truck loading.
1149
Caso de estudio
Prueba de exfoliación de bolsas de ostomía
Requisito Salts Healthcare, un fabricante y proveedor líder de productos para el cuidado de la salud, requería un sistema de baja capacidad para probar la integridad de sus productos hidrocoloides.