Search results
2626
[Page extract]
ASTM D3575
ASTM D3575 covers a number of tests for determining properties of polyethylene foams including compressive strength.
2627
[Page extract]
ASTM D2918
This test method provides data for assessing the durabilities of adhesive joints by means of T-peel type specimens stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temper
2628
[Page extract]
ASTM D5649-01
This test method is used to make comparative assessments of the securing or locking effect of adhesives used in threaded assemblies.
2629
[Page extract]
*corp Ikea IOS-TM-0057
This instruction describes preparation and testing of a board's ability to hold a fastener in up to three orientations
2630
[Page extract]
ASTM C598
This test method covers the determination of the annealing point and the strain point of a glass by measuring the rate of midpoint viscous bending of a simply loaded glass beam.
2631
[Page extract]
BS 1726-2
Springs, Helical springs, Cylindrical shape, Tensile loading, Circular shape, Wires, Bars (materials), Parallel, Dimensional tolerances, Form tolerances, Product specification, Ordering, Mechanical testing, Heat treatment
2632
[Page extract]
ISO 9727-2
This part of ISO 9727 specifies a test method for:
⎯ measuring the mass of cylindrical cork stoppers ready for use or semi-worked, totally or partially made of agglomerated cork, and
2633
[Page extract]
ASTM C651
This test method covers determination of the flexural strength of manufactured carbon and graphite articles using a simple beam in four-point loading at room temperature.
2634
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
2635
[Page extract]
*corp Ford DSEU
Test method covering measurement of door slam energy for Ford Chenai, India. Shows Mecmesin loadcell, display and special gripping fixtures. Note: Diagram shows a rigid link bar, which was later replaced by a flexible bungee connection.
2636
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
2637
Test Frame
Vortex-dv Prüfstand
Vortex-Prüfstand
Ein robuster zweisäuliger Prüfstand, mit dem man einen Drehmoment von bis zu 10 Nm (90 lbf.in) aufbringen kann. Groß und breit genug, um eine Vielzahl von Prüflingen aufzunehmen, und dennoch kompakt, um als Tischgerät verwendet zu werden…
2638
[Page extract]
ISO 9895
Specifies a method for determining the compressive strength in the machine and cross-directions of paper and board using a short-span compressive tester. It is intended for papers and boards used for the manufacture of containers and boxes.
2639
[Page extract]
BS EN 12311-2
BS EN 12311-2 is a test method for determining the tensile properties of flexible sheets used for waterproofing roofs.
2640
[Page extract]
BS ISO 7322
This International Standard specifies test methods for the determination of the following characteristics of composition cork (= product obtained from the agglutination of cork granules with the addition of a binder generally not derived from cork cells
2641
[Page extract]
BS EN ISO 14129
BS EN ISO 14129 is a test method used to determine the in-plane shear stress/shear strain response of fibre-reinforced plastic components.
2642
[Page extract]
ISO 9727-5
Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.
2643
[Page extract]
SAE J 1553
This SAE Recommended Practice describes a cross peel test method for use in measuring the bonding characteristics of automotive-type adhesives for joining fiber-reinforced plastics to themselves and to metals.
2644
[Page extract]
BS ISO 3384-1:2001+A1
BS ISO 3384-1 is a test method for determining the stress relaxation in compression of vulcanised rubber or thermoplastic.
2645
[Page extract]
FINAT FTM 9
This test method describes a means of assessing probably the most important and yet the hardest to measure property of pressure sensitive materials, the tack.
2646
[Page extract]
ISO 9073-3
Application of a force longitudinally to a test piece of a specified length and width at a constant rate of extension. Determination of values for breaking strength and elongation from the recorded force-elongation curve.
2647
[Page extract]
TAPPI T 840
This method describes a procedure for evaluating the adhesive used in glued lap joints of corrugated containers.
2648
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
2649
[Page extract]
ASTM F1304-18
ASTM F1304 is a test method used to determine the deflection of relatively rigid resilient floor tile such as vinyl composition tile and resilient flooring with a rigid polymeric core.
2650
[Page extract]
Special compression fixtures
Special compression fixtures have been specially designed to meet the challenges of a particular application.