Search results
1276
[Page extract]
Simplify data analysis in force, materials and torque testing
Test calculations are the values derived from raw measurement data, such as peak force, torque angle, or modulus of elasticity. With advanced software, these are now calculated instantly and with high precision, replacing error-prone manual methods.
1277
[Page extract]
FAQs about compressive strength testing
How is compressive strength different from tensile strength?
1278
[Page extract]
ASTM F1306
ASTM F1306, is a test method, which permits flexible barrier films and laminates to be characterised for slow rate penetration resistance to a driven probe.
1279
[Page extract]
Why Mecmesin for puncture resistance testing
Mecmesin designs and manufactures precision puncture resistance testing systems to meet the requirements of ASTM and ISO standards.
1280
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1281
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
1282
[Page extract]
Case studies and real-world examples
Food sachet packaging
In a recent study, our equipment was used to test the burst strength of multilayer foil sachets used for single-serve food products.
1283
[Page extract]
ISO 527-5
ISO 527-5 specifies the test conditions for the determination of the tensile properties of unidirectional fibre-reinforced plastic composites, based upon the general principles given in ISO 527-1.
1284
[Page extract]
Introduction to closure torque testing
Closure torque testing measures the rotational force required to apply or remove a closure, such as a bottle cap, jar lid, or other sealing component, from its container.
1285
[Page extract]
ASTM F543-13
This specification provides requirements for materials, finish and marking, care and handling, and the acceptable dimensions and tolerances for metallic bone screws that are implanted into bone.
1286
[Page extract]
ASTM D143
These test methods cover the determination of various strength and related properties of wood by testing small clear specimens.
1287
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
1288
Case study
ROPP Flaschendeckelverschluss-Drehmomenttest
Anforderung Brothers Drinks produziert und verpackt eine breite Palette alkoholischer und alkoholfreier Getränke mit Roll-on-Pilfer-Proof (ROPP) und Kronkorken.
1289
[Page extract]
How to Calculate UTS
This gives a value in N/mm² or MPa. During a tensile test, the material is pulled until it breaks. The highest recorded force, divided by the original cross-sectional area, gives the UTS. This value is the peak on a stress-strain curve.
1290
[Page extract]
ASTM D1709-03
These test methods cover the determination of the energy that causes plastic film to fail under specified conditions of impact of a free-falling dart.
1291
[Page extract]
Secant modulus testing with Mecmesin
Mecmesin testing systems such as the OmniTest and MultiTest-dV
1292
[Page extract]
ASTM D5934-02
ASTM D5934 specifies the use of controlled rate of loading mechanical instrumentation on rectangular plastic bars molded directly or cut from sheets, plates, or molded shapes via three-point loading bending techniques to obtain material properties such
1293
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1294
[Page extract]
What is lap shear testing under compression?
Lap shear testing under compressive load is a mechanical test used to determine the strength of adhesive joints subjected to shear forces while under compressive stress.
1295
[Page extract]
Industry applications and case examples
Heavy industrial packaging - A manufacturer supplying boxes for machine components integrated routine CMT testing to track performance trends.
1296
[Page extract]
ASTM D5748-95
This test method determines the resistance of a stretch wrap film to the penetration of a probe at a standard low rate, a single test velocity.
1297
[Page extract]
Mecmesin equipment for 180 degree peel testing
Mecmesin provides a complete range of test solutions designed for accurate and repeatable peel strength measurement.
1298
[Page extract]
ISO 1805
ISO 1805 specifies a method of testing the breaking force and knot breaking force of netting yarns for fishing nets.
1299
[Page extract]
What is texture testing?
Texture testing is the instrumental measurement of a product’s physical response to an applied force.
1300
[Page extract]
How is compression texture testing performed?
Test methods and parameters
A typical test places the sample on a stable platform beneath a compression plate or probe.