Search results
1251
[Page extract]
CETIE Guide 1
This guideline applies to the capping of still wines with a cork mouth finish as per CETIE data sheet GME 50.01 which has been used as a base for the European standard EN 12726. Contains reference to 'extraction force', 'cork dimensional recovery', 'ch
1252
[Page extract]
ASTM F2255-05
This test method is intended to provide a means for comparison of the adhesive strengths of tissue adhesives intended for use as surgical adhesives or sealants, or both, on soft tissue.
1253
[Page extract]
BS ISO 3597-2
ISO 3597-2 specifies a method for determining the flexural strength of composite rods of circular cross-section made of roving-reinforced resin.
1254
[Page extract]
ISO 12625-5
ISO 12625-5:2005 specifies a test method for the determination of the wet tensile strength of tissue paper and tissue products after soaking with water, using a tensile-strength-testing apparatus operating with a constant rate of elongation.
1255
[Page extract]
ASTM D624-00
This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
1256
[Page extract]
BS EN ISO 6892-2
BS EN ISO 6892-2 specifies a method of tensile testing of metallic materials at temperatures higher than room temperature.
1258
[Page extract]
BS EN 14372
This document establishes minimum safety requirements and specifies appropriate test methods for children’s cutlery and feeding utensils designed for the use of children aged up to 3 years, with or without parental supervision.
1259
[Page extract]
ASTM D349
These test methods cover the procedures for testing rigid round rods used in electrical insulation.
1260
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
1261
[Page extract]
ASTM D2919
This test method covers data for assessing the durability of adhesive lap-shear joints while stressed in contact with air, air in equilibrium with certain solutions, water, aqueous solutions, or other environments at various temperatures.
1262
Event
Cap Closure and Removal Torque Testing
The primary objective for measuring and analyzing the torque characteristics of a container cap is to accurately determine not only the quality of the part or process, but also the root cause of a wide variety of defects.
1263
[Page extract]
BS EN ISO 9004
BS EN ISO 9004 provides guidance on achieving sustainable success through quality management. The European standard can be applied to all organisations across all sectors.
1264
[Page extract]
ISO 594-2
ISO 594 and EN 1707 contain 8 separate tests, some of which are only applicable to Luer lock fittings. Most of these tests require that the sample be assembled to a particular precision steel reference fitting.
1265
[Page extract]
ASTM D3528
This test method covers the determination of the tensile shear strengths of adhesives for bonding metals when tested in an essentially peel-free standard specimen that develops adhesive stress distribution representative of that developed in a typical l
1266
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1267
[Page extract]
ASTM C158
These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. These test methods are applicable to annealed and prestressed glasses and glass-ceramics available in varied forms.
1268
[Page extract]
ISO 9727-2
This part of ISO 9727 specifies a test method for:
⎯ measuring the mass of cylindrical cork stoppers ready for use or semi-worked, totally or partially made of agglomerated cork, and
1269
[Page extract]
ASTM D903-98
ASTM D903 is a test procedure used to determine the strength of adhesive bonds.
1270
[Page extract]
ASTM D3658
This test method covers the simplistic comparison of strengths of glass/metal joints when the adhesive is cured by ultraviolet (UV) radiation and standard specimens are used and tested under specified conditions of preparation, radiation, and load.
1271
Event
Tensile Testing: Extension, Elongation, Force & Failure
The primary objective for measuring and analyzing the the tensile force value of a product is to accurately determine one or more of these factors:
1272
[Page extract]
ISO 14126
ISO 14126 outlines procedures for determining the compressive properties of fibre-reinforced plastics composites in the in-plane direction. Two methods are detailed in the standard:
1273
[Page extract]
ISO 283
ISO 283 specifies a test method for the determination of the full thickness tensile strength in the longitudinal direction and the elongation at the reference force and breaking point of conveyor belts having a textile carcass.
1274
[Page extract]
EN TS 15945
The purpose of DD CEN/TS 15945 is to specify test methods to evaluate the ease of opening of consumer packages, in order to improve easy access to the contents. For packages regulated for safety or similar reasons, e.g.
1275
Event
2022 Medical Technology Ireland, Galway, Ireland - We would love to see you there!
Who should attend?
Quality Managers and design/product engineers involved in the development and production of medical and pharmaceutical devices and packaging.
What is the exhibition about?