Search results
726
Event
Understanding Adhesion Strength: 180 Degree Peel Test
Across many households and industries, consumers have developed a strong preference for and confidence in ‘Duct Tape’ for all types of uses and applications. This is mainly due to the adhesion strength.
727
Case study
Torsion spring testing
Customised engineering example
Unlike most compression and tension springs, torsion springs are produced in a variety of forms with differing leg positions.
728
[Page extract]
ASTM D2148
ASTM D2148 is a test standard that for testing bondable silicone rubber tapes, which form a sealed structure either with the application of heat (and pressure if needed) or by the process of auto-adhesion (self-fusing).
729
[Page extract]
BS EN ISO 4624
Describes methods for determining the adhesion by carrying out a pull-off test on a single coating or a multi-coat system of paint, varnish or related product.
730
[Page extract]
ISO 7622-2
ISO 7622-2 specifies a method for the determination of the tensile strength, in the longitudinal, of steel cords constituting the carcass of conveyor belts.
It applies exclusively to conveyor belts with a steel carcass.
732
Case study
Thermogeformte Kunststoffverpackungen mit Scharnierreiß- und Einrastfunktion
Anforderung Par-Pak Europe Ltd stellt tiefgezogene Kunststoffbehälter und -schalen für die Verpackung, den Einzelhandel und den Vertrieb in der Lebensmittelindustrie her.
733
Event
Fundamentals of Food Texture Testing
Texture cannot be controlled unless it is measured in a consistent and repeatable manner.
734
[Page extract]
BS EN 12697-23
This standard specifies a test method for determining the (splitting) indirect tensile strength of cylindrical specimens of bituminous mixtures.
735
[Page extract]
ISO 9727-5
Specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper.
736
[Page extract]
IEC 61210
IEC 61210:2010 applies to non-insulated flat quick-connect terminations consisting of a male tab of size 2,8 mm, 4,8 mm, 6,3 mm or 9,5 mm with hole or dimple detents and a mating female connector for use as either an incorporated or an integrated part o
738
Case study
Verformungstests von Kfz-Außenspiegeln
Anforderung Murakami Ampas (Thailand) ist ein bedeutender Lieferant von Spiegelsystemen für die Automobilindustrie.
740
Case study
Thermoformed plastic packaging hinge tear and pop-lock engagement
Requirement
Par-Pak Europe Ltd manufacture thermoformed plastic containers and trays for packing, retail and distribution in the food industry.
741
[Page extract]
BS EN ISO 1856
BS EN ISO 1856 is a test method that specifies three methods for determining the compression set of flexible cellular materials and applies only to latex and polyurethane foams of thickness greater than 2 mm.
742
Case study
Hot air balloon cloth tensile strength and tear-resistance testing
Requirement
Ultramagic is the second largest hot air balloon manufacturer in the world.
For obvious safety reasons, the material used must conform to strict standards applicable to the aeronautical industry.
743
Case study
Kindersicherer Verschlussdorn (CRC)
Beispiel für kundenspezifisches Engineering Kindersichere Verschlüsse (Child Resistant Closures, CRC) erfordern eine ausreichende vertikale Kraft, um den CR-Verriegelungsmechanismus zu aktivieren, bevor das Drehmoment angewendet wird.
744
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
745
[Page extract]
ISO 13955
ISO 13955 is used to assess the cohesion of a PE pipe/electrofusion socket or saddle assembly. Applicable to pipes with a nominal outside diameter between 16 mm and 225 mm
746
[Page extract]
Applications of compressive modulus testing
Compressive modulus data is essential in sectors where compressive stiffness determines performance and safety.
747
Case study
Dialysis needle sharpness test for patient comfort
Requirement
Kawasumi Laboratories Inc. was founded in 1957 as Japan’s first manufacturer of disposable plastic medical devices for blood collection and transfusion purposes.
748
[Page extract]
ISO 37
ISO 37 specifies a method for the determination of the tensile stress-strain properties of vulcanized and thermoplastic rubbers.
This test standard is equivalent to BS ISO 37.
749
Case study
Page pull strength test
Requirement
Mecmesin collaborated with a customer to design and develop a force measurement system to determine book binding adhesive strength in retaining individual pages.
750
[Page extract]
TAPPI T 549
This method describes a horizontal plane procedure for the determination of the coefficient of static and kinetic friction of paper measured when sliding against itself.