Search results
376
Accessory
Cone Point - 12 mm diameter, 5 kN, 5-16 UNC
432-359
A Cone Point probe of Ø 12.7 mm with angle of 60°.
For compression testing of various components or materials up to 5 kN.
Typically used where compressive force needs to be applied at a point or for penetration into a material over a short distance.…
377
Accessory
Pyramiden Backen für Mec227 Kleiner Schraubspannkopf, 100 N, 10 x 25 mm
Mec227-BP25
Pyramiden Backen (10 mm hoch x 25 mm breit) - vernickelt mit einer Oberfläche aus 1,2 mm hohen gehärteten Stahlpyramiden.
Öffnungsweite = 0 - 8mm.
Für flache Proben von Materialien, die einen "Biss" benötigen, um ein gute Klemmen zu gewährleisten (z. B…
378
Accessory
3-Point Bend Jig, 1 kN, Aluminium, T-slot base
432-248
A lightweight 3-point Bend Jig with 60 mm high upper and lower anvils of 1.5mm radius. Has a support span up to 120 mm.
Ideal for most low-force bending and snapping applications.
For use with T-slot base plate (432-294) - sold separately - to fit…
379
Accessory
Floating Peel Jig (ISO 10373-1), 500 N, 10-32 UNF
432-413
The Floating Peel Jig is used to test the peel strength between adhesive layers of flat, rigid samples such as credit cards.
A portion of the top layer is placed between the rollers and held in an upper grip (order separately). As load is applied the…
380
Accessory
Diamant Backen für Mec240k Schraubspannkopf, 2.5 kN, 30 x 30mm
Mec240k-BD
Diamantenbacken (30 mm hoch x 30 mm breit) - vernickelt und bechichtet mit synthesischen Diamanten.
Öffnungsweite = Je nach Spannzeugtyp - siehe Datenblatt.
Für flache Proben von Materialien, die einen "Biss" benötigen, um ein gute Klemmen zu…
381
Accessory
Cable Cam grip for CrimpTest-1 kN
432-660
Cable Cam Grip for CrimpTest-1 Tester (supplied as standard with the Tester)
The Cable Cam Grip is designed for holding insulated cables and wire when tensile testing the pull strength of terminals up to 1 kN.
The cable is secured by the serrated cam,…
382
Accessory
Pyramiden Backen für Keilspannzeug MecS622, Öffnungsweite 0 bis 9 mm
MecS622-BP
Pyramiden Backen (40 mm hoch x 34 mm breit) - vernickelt mit einer Oberfläche aus 1,2 mm hohen gehärteten Stahlpyramiden. Öffnungsweite = 0 - 9mm.
Für flache Proben von Materialien, die einen "Biss" benötigen, um ein gute Klemmen zu gewährleisten (z. B.…
383
Accessory
Pyramiden Backen für MEC243 Keilspannzeug 20 & 50kN, 50 x 35mm, Öffnungsweite 0 - 13mm
Mec243-BP
Pyramiden Backen (50 mm hoch x 35 mm breit) - vernickelt mit einer Oberfläche aus 1,2 mm hohen gehärteten Stahlpyramiden.
Öffnungsweite = 0-13mm.
Für flache Proben von Materialien, die einen "Biss" benötigen, um ein gute Klemmen zu gewährleisten (z. B…
384
Case study
Torque to twist out a champagne cork
Requirement
Sibel manufacture natural corks for the wine and spirits industry in the Champagne region of France. They pride themselves on working closely with their clients, taking into account their requirements and expectations for safety.
386
Case study
Vial stopper needle penetrability residual seal force and torque testing
Requirement
COVID-19 vaccines, as parenteral medications, enter the body by injection through the tissue and circulatory system.
387
[Page extract]
Introduction to tension and compression testing
Tension and compression testing are among the most widely used mechanical testing methods for evaluating how a material or component performs under applied loads.
388
[Page extract]
Mecmesin solutions for rotational shear testing
Mecmesin provides torque testing systems designed for high-precision, repeatable results in rotational shear testing.
389
[Page extract]
Equipment and procedures
A flat crush tester comprises two smooth, parallel platens, one fixed and one moving under controlled load application. The conditioned specimen is placed between the platens with flutes oriented vertically.
390
[Page extract]
What is a three-point bend test?
A three-point bend test is a widely used method for determining the flexural properties of materials. It involves applying a load at the midpoint of a specimen supported at two points, creating a bending force.
391
[Page extract]
Methods of testing tensile strength
The most common method is the uniaxial tensile test.
392
[Page extract]
How shear testing works
Food shear testing replicates cutting or slicing actions. A blade or fixture is passed through a sample while the force required is recorded. The process generally includes:
393
[Page extract]
How peel wheel tests are conducted
Specimen preparation – The bonded material is cut to defined dimensions, ensuring uniformity of size and adhesive application.
394
[Page extract]
Selecting the right running torque testing solution
When specifying a running torque test system, engineers should consider:
395
[Page extract]
What is elongation at break?
Elongation at break measures how much a material can stretch before it fractures. Expressed as a percentage of the original gauge length, it is a key indicator of ductility and toughness.
396
[Page extract]
Equipment for burst testing
The right equipment depends on the container type, material, and applicable standard.
397
[Page extract]
Tensile deformation and its significance
Tensile deformation occurs when a material is stretched by an axial load, causing it to elongate.
398
[Page extract]
Case studies and real-world examples
Mecmesin’s systems have been used across a range of industrial applications:
399
[Page extract]
Introduction to compression testing
Compression testing is a core mechanical test method used to evaluate how materials and products behave when subjected to a compressive load.
400
[Page extract]
Methods of compressive burst testing
Inflationary burst testing
In this method, internal pressure is gradually increased using air, gas, or liquid until the container ruptures. This is widely applied to: