Search results
2401
[Page extract]
ASTM D905-08
This test method covers the determination of the comparative shear strengths of adhesive bonds used for bonding wood and other similar materials, when tested on a standard specimen under specified conditions of preparation, conditioning, and loading in
2402
[Page extract]
ISBT PTC-00002
This ISBT (International Society of Beverage Technologists) publication outlines dimensional and physical characterization and performance test methods for PET beverage bottles for use in CSD (Carbonated Soft Drink), Hotfill, and Cold Fill applications.
2403
[Page extract]
Mechanische Kraftmessgeräte
Mechanische Kraftmessgeräte arbeiten nach dem Federprinzip und zeigen die an der Messwelle einwirkende Kraft auf einem analgoen Zifferblatt an.
2404
[Page extract]
ASTM C158
These test methods cover the determination of the modulus of rupture in bending of glass and glass-ceramics. These test methods are applicable to annealed and prestressed glasses and glass-ceramics available in varied forms.
2405
[Page extract]
ISO 13955
ISO 13955 is used to assess the cohesion of a PE pipe/electrofusion socket or saddle assembly. Applicable to pipes with a nominal outside diameter between 16 mm and 225 mm
2406
[Page extract]
BS EN 3841-509
This standard specifies a method of determining the forces required to insert and extract the contact pin into and out of the terminal socket of the signal contact. It shall be used together with EN 3841-100.
2407
[Page extract]
BS 6319-2
BS 6319-2 is a test method for determining the compressive strength of resin and polymer/cement compositions used in construction.
2408
[Page extract]
BS EN ISO 7886-1
This document specifies requirements and test methods for verifying the design of empty sterile single use hypodermic syringes, with or without needle, made of plastic or other materials and intended for the aspiration and injection of fluids after fill
2409
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
2410
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
2411
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2412
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
2413
[Page extract]
BS ISO 11040-4
This part of ISO 11040 applies to — tubing-glass barrels (single-chamber design) for injection preparations, and — sterilized subassembled syringes ready for filling.
2415
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
2416
[Page extract]
CETIE Guide 5
This document gives background information and recommended best practices for the application of plastic flat-top screw-on caps onto PET bottles for beverages. It covers all closure sizes and beverage product types.
2417
[Page extract]
ASTM D3846
ASTM D3486 is a test method used for evaluating the in-plane strength of reinforced thermosetting plastics in flat sheet form in thicknesses ranging from 2.54 to 6.60 mm.
2418
[Page extract]
ISO 1924-2
Specifies a method for measuring the tensile strength, strain at break and tensile energy absorption of paper and board, using a testing machine operating at a constant rate of elongation (20 mm/min).
2419
[Page extract]
ASTM D3810
This test method covers the determination of or the recommendation for minimum application torque that results in a fully degraded removal torque that is at a level greater than the maximum expected reverse-ratchet torque for a Type IA child-resistant c
2420
[Page extract]
ASTM B913
This test method establishes the requirements for a standardized method of evaluating the quality of crimped-type electrical connections to solid or stranded conductors.
2421
[Page extract]
ISO 34-1
ISO 34-1 measures tear strength test methods for rubber test samples. The test results in measurement of a materials resistance to tearing. Tear strength can also be used to monitor material anisotropy of a material.
2422
[Page extract]
ISO 7439
ISO 7439:2002 is applicable to single-use copper-bearing intra-uterine contraceptive devices and their insertion instruments.
2423
[Page extract]
ISO 8067
ISO 8067 specifies two methods for the determination of the tear strength of flexible cellular polymeric materials:
Method A, using a trouser test piece
Method B, using an angle test piece without a nick
2424
[Page extract]
ASTM E2658-15
These practices cover procedures and requirements for the calibration and verification of testing machine speed by means of standards calibration devices
2425
[Page extract]
ASTM D4541-09e1
This test method uses a class of apparatus known as portable pull-off adhesion testers. They are capable of applying a concentric load and counter load to a single surface so that coatings can be tested even though only one side is accessible.