Search results
3001
[Page extract]
ASTM D7834-13
During the application of coatings, paint brushes can exhibit shedding of filling material onto the coated surface. A measure of this shedding filling material will determine the paint brush’s ability to resist shedding during application.
3002
[Page extract]
BS 5081-1
A mechanical testing machine is used to move the syringe plunger and to aspirate and expel water, whilst the force exerted and the plunger travel are recorded.
3003
[Page extract]
TAPPI T 824
This test evaluates the ability of corrugating medium to contribute to the compression strength of a corrugated box.
3004
[Page extract]
ASTM D2653
ASTM D2653 determines the tensile properties of elastomeric yarns made from natural rubber, spandex or other elastomers.
3005
[Page extract]
TAPPI T 810
This method describes a procedure for measuring the bursting strength of single wall and double wall corrugated board within the range of 690 kPa (100psi) to 4825 kPa (700 psi) employing an instrument which uses a disk shaped, molded diaphragm.
3006
[Page extract]
ASTM D7264 / D7264M-15
ASTM D7264 is a test method used to determine the flexural stiffness and strength properties of polymer matrix composites. The test method summarises two procedures:
3007
[Page extract]
DIN EN 61238-1
Electric connectors, Crimped connectors, Electric cables, Power cables, Electric conductors, Electric wires, Copper, Aluminium, Temperature, Classification systems, Type testing, Short-circuit current tests, Resistance measurement, Mechanical testing, T
3008
[Page extract]
ASTM D3807
ASTM D3807 is a test method used to determine the strength properties of adhesives in cleavage peel by tension loading. It allows the comparative testing of cleavage/peel strengths of bonded engineering thermoplastic adherends.
3009
[Page extract]
ASTM F1473-18
ASTM F1473 is a test method determines the resistance of polyethylene materials to slow crack growth. It is also known as PENT (Pennsylvania Notch Test) test.
3010
[Page extract]
ISO 188
ISO 188:2011 specifies accelerated ageing or heat resistance tests on vulcanized or thermoplastic rubbers. Two methods are given:
3011
[Page extract]
BS EN 671-1
Fire hydrants, Fire hoses, Firefighting equipment, Flexible pipes, Fire hose reels, Hose reels, Fire safety in buildings, Performance, Approval testing, Corrosion tests, Ageing tests, Flow measurement, Endurance testing, Impact testing, Pressure testing
3012
[Page extract]
BS EN ISO 10619-1
BS EN ISO 10619-1 is a test method covering bending tests on rubber or plastics hoses and tubing.
3013
[Page extract]
DIN 6094
Dimensions and specifications for a series of bottle finishes, including corks, crown, screw threads, including bottles with internal pressure.
3014
[Page extract]
GS1 5.0
The Hanger Specifications are intended to increase efficiency in the supplier-to-retailer pipeline by minimizing order-to-sales floor cycle time.
3015
[Page extract]
BS EN 12562
Synthetic fibres, Polyamide fibres, Aramide fibres, Textile products, Textile testing, Yarn, Filament yarns, Filaments, Filament (textile fibre), Yarn testing, Yarn linear density determination, Elongation at fracture, Elongation, Force measurement, Mec
3016
[Page extract]
BS EN 12568
Protective footwear, Protective clothing, Toe-caps, Metals, Non-metals, Impact strength, Performance testing, Dimensions, Length, Impact testing, Compression testing, Penetration tests, Corrosion resistance, Corrosion tests, Bend testing, Marking, Test
3017
[Page extract]
ASTM D2718
These test methods determine the shear properties of structural panels associated with shear distortion of the planes parallel to the edge planes of the panels. Both shear strength and modulus of rigidity may be determined.
3018
Event
Materials Testing: Theory and Practice Pt. 2
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
3019
[Page extract]
BS EN ISO 10618
Carbon fibres, Mechanical properties of materials, Tensile strength, Tensile testing, Plastics, Impregnated materials, Yarn, Modulus of elasticity, Strain, Tensile strain, Loading, Reinforcing materials, Composite materials, Test equipment, Test specime
3020
[Page extract]
ISO 1924-1
Applies, within the limitations of the instruments used, to all papers and boards with the exception of corrugated board, but may be applied to the components of such board. Specifies the method which causes failure of the piece in a mean time of 20 s.
3021
[Page extract]
UL 486A-B
UL 486A-B is a safety standard that outlines the requirements for wire connectors and soldering lugs used with electrical conductors.
3022
[Page extract]
ISO 3037
Specifies an unwaxed edge method for the determination of the edgewise crush resistance of corrugated fibreboard. It is applicable to all corrugated fibreboard grades.
3023
Event
Materials Testing: Theory and Practice Pt. 1
Materials testing is often the last step in the manufacturing process. Yet, quality is the result of both the process and the material. If the material that goes into the product is inadequate or defective, then the product may be deficient or faulty.
3024
[Page extract]
ASTM D6243-09
This test method covers a procedure for determining the internal shear resistance of a Geosynthetic Clay Liner (GCL) or the interface shear resistance between the GCL and an adjacent material under a constant rate of displacement or constant stress.