Search results
2601
[Page extract]
ISO 1966
Describes the design requirements and tests for the crimping of insulated and non-insulated terminations to general purpose cables, with conductors of copper, copper alloy, aluminium or aluminium alloy, in locations in which the stabilized conductor tem
2602
[Page extract]
ASTM D3787
This test method describes the measurement for bursting strength with a ball burst strength tester of textiles or garments that exhibit a high degree of ultimate elongation.
2603
Case study
Glasspritze Luer-Lock-Aufsatz abziehbar
Beispiel für kundenspezifisches Engineering Polycarbonat-Luer-Lock-Adapter werden reibschlüssig auf Glasspritzendüsen aufgesteckt. Die Qualitätssicherung verlangt, dass sie bei normalem Gebrauch nicht frei werden können.
2604
[Page extract]
ISO 178
ISO 178 is a test method for the determination of flexural properties of rigid and semi-rigid plastics. These properties include flexural modulus and flexural strength.
2605
[Page extract]
TAPPI T 804
This method is used for measuring the ability of corrugated or solid fiber shipping containers to resist external compressive forces.
2606
[Page extract]
TAPPI T 807
This method describes a procedure for measuring the bursting strength of linerboard using a disk shaped diaphragm. Basis weights for this method should be 98 g/m (20#/MSF) and higher. The minimum burst should be 350 kPa (51 psi).
2607
Page
Sie haben den Mecmesin-Newsletter abonniert
Danke
Wir wünschen Ihnen viel Spaß mit den regelmäßigen Updates zu unseren Entwicklungen bei Kraft-, Material- und Drehmomentprüfungen.
2608
[Page extract]
ISO 814
ISO 814 specifies a method for determining the adhesion strength of rubber-to-metal bonds where the rubber part is assembled between two parallel metal plates, using the adhesive system under investigation
2609
[Page extract]
BS EN ISO 4074
BS EN ISO 4074:2002 specifies the minimum requirements and the test methods to be used for condoms made from natural rubber latex which are supplied to consumers for contraceptive purposes and to assist in the prevention of sexually transmitted infectio
2610
[Page extract]
ASTM D2527
ASTM D2527 covers the strength and appearance of the splice in vulcanized rubber-seal material of any size, type, or cross-sectional shape.
2611
[Page extract]
ASTM E855-08
This standard describes three test methods for determining the modulus of elasticity in bending and the bending strength of metallic strips or sheets intended for the use in flat springs.
2612
[Page extract]
BS EN 12814-6
BS EN 12814-6 is a low temperature tensile test method for testing welded joints of thermoplastics semi-finished products.
2613
Case study
Seed bottle closure torque testing
Requirement
The Royal Botanic Gardens, Kew, have undertaken an international conservation initiative to preserve seed specimens of over 24,000 plant species, protecting them from extinction at the Millennium Seed Bank at Wakehurst Place, West
2614
[Page extract]
*corp 01M-01-225
Determination of the Elongation, Recovery and Modulus of Elastic Fabrics.
A fabric specimen of specified dimensions is extended at a constant rate to a specified force for three cycles.
2615
[Page extract]
BS EN ISO 10066
BS EN ISO 10066 is a test method for determining creep in tension of flexible cellular polymeric materials.
2616
Event
Fundamentals of Food Texture Testing
Texture cannot be controlled unless it is measured in a consistent and repeatable manner.
2617
[Page extract]
Standards for yield point testing
Yield point testing protocols are defined by recognised international standards, including:
2618
[Page extract]
USP <381>
This chapter applies to closures used for long-term storage of preparations defined in the general test chapter Packaging and Storage Requirements á659ñ, Injection Packaging.
2619
[Page extract]
ASTM D2534
The coefficient of friction is related to the slip properties of many commercial articles that have been coated with petroleum wax (for example, butter cartons and wax-impregnated or hot melt coated corrugated board).
2620
Case study
Kostengünstige Prüfung der Kabelstärke
Beispiel für kundenspezifisches Engineering Ein bedeutender Hersteller von Kabelbäumen und Steckverbindern wandte sich an uns, um eine kostengünstige Lösung für Zugkraftprüfkabel mit unterschiedlichen Durchmessern und direkt gebondeten Verbin
2621
[Page extract]
BS EN ISO 13127
This standard is only to verify that panel-tested closures with minor modifications are still compliant, by applying mechanical tests as more economical than further full panel tests with children and with adults.
2622
[Page extract]
ASTM C1469
This test method covers the determination of shear strength of joints in advanced ceramics at ambient temperature.
2623
[Page extract]
ISO 12048
Specifies a method for testing the resistance to compression of complete, filled transport packages and a method for carrying out a stacking test on complete, filled transport packages using the same apparatus.
2624
[Page extract]
EN 14509
This draft European Standard is submitted to CEN members for second formal vote. It has been drawn up by the Technical Committee
CEN/TC 128.
This covers a very wide range of tests including coatings, strengths etc.
2625
[Page extract]
ASTM D3165
This test method is useful in that the joint configuration closely simulates the actual joint configuration of many bonded assemblies.