Search results
2451
Case study
Druckfestigkeitsprüfung von Katalysatorpellets
Anforderung
Katalysatoren werden häufig in industriellen Prozessen eingesetzt, bei denen es auf Ausbeute und Zeit ankommt, um ein Produkt so schnell wie möglich zu bilden.
2452
Software
Emperor Force Software
Emperor™ Force-Software Benutzerfreundliche Software mit nahezu unbegrenzter Freiheit bei der Gestaltung und Anpassung von Zug- und Druckprüfungen an Ihre Anforderungen. Emperor™ wurde von Mecmesin in enger Zusammenarbeit mit unseren Kunden entwickelt und…
2453
Case study
Extraktionstests von Whiskey-Stopfen
Anforderung Um die Qualität und Lagerung ihres Premium-Produkts im Wert von 1000 US-Dollar zu verbessern, musste das Forschungs- und Entwicklungsteam eines führenden schottischen Whiskyherstellers das Design seiner Flaschenverschlüsse optimie
2454
[Page extract]
Mechanische Kraftmessgeräte
Mechanische Kraftmessgeräte arbeiten nach dem Federprinzip und zeigen die an der Messwelle einwirkende Kraft auf einem analgoen Zifferblatt an.
2456
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
2457
[Page extract]
ASTM D3330
These test methods cover the measurement of the peel adhesion of single and double-sided pressure-sensitive tapes.
2458
[Page extract]
ASTM D905-08
This test method covers the determination of the comparative shear strengths of adhesive bonds used for bonding wood and other similar materials, when tested on a standard specimen under specified conditions of preparation, conditioning, and loading in
2460
[Page extract]
ASTM C674
These test methods cover determination of the modulus of rupture and the modulus of elasticity of fired ceramic whitewares bodies, formed by any fabrication method, and are applicable to both glazed and unglazed test specimens.
2461
[Page extract]
ISO 7886-4
This document specifies requirements for sterile single-use hypodermic syringes made of plastic and rubber materials with or without needle, and intended for the aspiration of fluids or for the injection of fluids immediately after filling and of design
2462
[Page extract]
ISO 12192
Specifies a method for the determination of the edgewise compressive strength (ring crush resistance) of paper and paperboard, especially board used in the manufacture of fibreboard shipping containers.
2463
[Page extract]
ASTM F806-99a
ASTM F806 is a test method that covers determination of the short-time compressibility and recovery at room temperature of laminated composite gasket materials.
2464
[Page extract]
BS 2782-3: 360C
BS 2782-3: Method 360C specifies a test method for testing the tear resistance of plastics film and sheeting by the initiation method
2466
[Page extract]
ISO 34-1
ISO 34-1 measures tear strength test methods for rubber test samples. The test results in measurement of a materials resistance to tearing. Tear strength can also be used to monitor material anisotropy of a material.
2467
[Page extract]
ASTM D5083-17
ASTM D5083 is a test method for measuring the force required to break a reinforced thermoset plastic specimen and the extent to which the specimen stretches or elongates to that breaking point.
2469
[Page extract]
ASTM D6117-18
ASTM D6117 covers the evaluation of fastener use with “as manufactured” plastic lumber and shapes through the use of two different testing procedures:
2470
[Page extract]
ASTM D876 - 13
ASTM D876 is a test method covering the testing of general-purpose (Grade A), low-temperature (Grade B), and high-temperature (Grade C)2 non-rigid vinyl chloride polymer tubing, or its copolymers with other materials, for use as electrical insulation.
2471
[Page extract]
BS EN ISO 7864
BS EN ISO 7864:2016 specifies requirements for sterile hypodermic needles for single use of designated metric sizes 0,18 mm to 1,2 mm.
2472
[Page extract]
FINAT FTM1
This test method is designed to quantify the permanence of adhesion or peelability of self-adhesive pressure sensitive) materials.
2473
[Page extract]
ASTM D5034-09
This test method covers the grab and modified grab test procedures for determining the breaking strength and elongation of most textile fabrics. Provisions are made for wet testing.
2474
[Page extract]
BS EN ISO 11608-2
Specifies requirements and test methods for single-use, double-ended, sterile needles for needle-based injection systems (NISs) that fulfil the specifications of ISO 11608-1.