Search results
2001
Test Frame
Vortex test frame
Vortex test frame
A sturdy twin-column test frame capable of applying torque up to 10 N.m (90 lbf.in). Tall and wide enough to accept a variety of test specimens yet compact to use as a bench-top tester.
View test frame
2002
[Page extract]
ASTM D2633
ASTM D2633 test methods cover procedures for the testing of thermoplastic insulations and jackets used on insulated wire and cable.
2003
Case study
Top-Load-Prüfung von Flaschen aus pflanzlichem PLA-Material
Anforderung
BioPak Solutions in Roquefort-les-Pins, Frankreich, ist führend in der Herstellung von Flaschen aus Polymilchsäure (PLA).
2004
[Page extract]
ASTM D926-17
ASTM D926 is a test method that covers the determination of plasticity and recovery of unvulcanized rubber by means of the parallel plate plastometer. Uncompounded, compounded, and reclaim rubber may be tested.
2005
[Page extract]
BS EN ISO 12230
This European Standard specifies a method for the determination of the tensile properties of materials used as surfaces for sports areas.
2006
[Page extract]
ASTM D3914
ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.
2007
[Page extract]
ASTM C364
This test method covers the compressive properties of structural sandwich construction in a direction parallel to the sandwich facing plane.
2008
Case study
Pneumatische Topload-Steuerung für die Prüfung des CRC-Kappendrehmoments
Beispiel für kundenspezifisches Engineering Bei der Prüfung des Drehmoments von kindersicheren Flaschenverschlüssen muss gleichzeitig eine Höchstlast aufgebracht werden.
2009
[Page extract]
ASTM D5467 / D5467M-97
ASTM D5467 is a test method that determines the in-plane compressive properties of polymer matrix composite materials reinforced by high-modulus fibers in a sandwich beam configuration.
2010
[Page extract]
BS EN 17394-2
This document defines a test method for security of attachment of functional and decorative buttons to clothing including garments such as gloves, hats, scarves, hosiery, ties, and textile belts. The scope of this document is limited to sewn-on buttons,
2011
[Page extract]
ASTM F904
ASTM F904 is a test method that covers a procedure for comparing the bond strength or ply adhesion of similar laminates made from flexible materials such as cellulose, paper, plastic film, and foil.
2012
[Page extract]
ASTM F37-00
1.1 These test methods provide a means of evaluating the sealing properties of sheet and solid form-in-place gasket materials at room temperature.
2013
[Page extract]
ISO 527-3
ISO 527-3 specifies the conditions for determining the tensile properties of plastic films or sheets less than 1 mm thick, based upon the general principles given in ISO 527-1.
2014
Case study
Zugversuch an gelöteten Flexikreisen
Anforderung Der Kunde war Hersteller und Entwickler von Bremssystemen für die Nutzfahrzeug-, Bus- und LKW-Industrie.
2015
[Page extract]
ASTM C1147
ASTM C1147 testing covers the evaluation of joints between two pieces of weldable grades of thermoplastic material. This testing is intended to establish methods to evaluate minimum short term weld factors.
2016
[Page extract]
ASTM D380
ASTM D380 is a set of test methods for determining testing and inspection procedures for rubber hoses e.g. hydraulic hoses and automotive hoses.
2017
[Page extract]
Digitale Kraftmessgeräte
Die digitalen Kraftmessgeräte von Mecmesin bieten hervorragende Genauigkeit und Erschwinglichkeit.
2019
Case study
Drehmomentprüfung Schönheitsproduktverschlüsse
Anforderung Ein Hersteller einer breiten Palette von Haut-, Haarpflege-, Make-up- und Sonnenschutzprodukten mit Sitz in Griechenland musste seine veralteten Drehmomentprüfgeräte durch moderne digitale Drehmomentprüfgeräte ersetzen, um die Pro
2020
[Page extract]
ASTM D3983
This test method describes a method of measuring the shear modulus and rupture stress in shear of adhesives in bonded joints.
2021
Case study
Prüfung des Drehmoments der Schraubenfeder
Anforderung Gefederte Komponenten werden häufig in Haushalts- und Konsumgütern verwendet: Wäscheklammern, Clips und altmodische Mausefallen; kleine Türen und Klappen an Kameras oder HiFi-Geräten; Große Türen und Verschlüsse, z. B.
2022
[Page extract]
CETIE Guide 7
This guideline applies to the screw capping of still wines with a metallic closure having a threaded plastic insert and a tamper-evident band which needs to be snapped before it can be opened. The closure is screwed and crimped during capping.
2024
[Page extract]
ISO 4049
This document specifies requirements for dental polymer-based restorative materials supplied in a form suitable for mechanical mixing, hand-mixing, or intra-oral and extra-oral external energy activation, and intended for use primarily for the direct or
2025
[Page extract]
ASTM D3481
This test method covers the measurement of the force required to separate (or “shell”) the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.