Search results
1801
[Page extract]
Why Mecmesin?
With over 40 years of experience, Mecmesin delivers torque testing systems that are precise, easy to use, and fully supported.
1802
[Page extract]
Introduction to double rip tongue tear testing
Double rip tongue tear testing is a recognised method for assessing the tear resistance of flexible materials including co
1803
[Page extract]
Loop tack test procedure
Sample preparation
Cut adhesive strips to the required length and width stated in the chosen standard. Condition the samples at the specified temperature and humidity before testing.
1804
[Page extract]
Types of edge crush tests and methodologies
TAPPI and ISO standards
ECT is governed by internationally recognised standards that ensure accuracy, repeatability, and comparability of results.
1805
[Page extract]
How to conduct a floating roller peel test
Carrying out this test requires attention to detail and strict adherence to the procedure. Key steps include:
1806
[Page extract]
Common challenges and solutions
Misalignment can cause uneven peeling forces.
1807
[Page extract]
Speak to an expert
Mecmesin has decades of experience in tear resistance testing and offers complete solutions for single rip trouser tear applications.
1808
[Page extract]
Standards and specifications
Fastening torque testing is governed by international and sector-specific standards to ensure consistency and repeatability:
1809
[Page extract]
Introduction to equibiaxial flexure compression testing
Equibiaxial flexure compression testing is a materials testing method used to evaluate a specimen’s resistance to bending under multi-directional loading.
1810
[Page extract]
Equipment and tools used in testing
Accurate elongation and recovery testing requires tensile testing machines capable of precise load application and displacement measurement. Important features include:
1811
[Page extract]
Why is the trapezoidal tear test important?
Tear resistance is a critical measure of a material’s durability, particularly in applications where the material may be subject to punctures, cuts, or repeated stress.
1812
[Page extract]
Speak to an expert
If you need needle penetration testing for compliance, product validation, or quality control, Mecmesin’s technical specialists can recommend the right solution for your requirements.
1813
[Page extract]
Speak to an Expert
The Concora Crush Test, as defined in TAPPI T 824, is a critical step in corrugated medium evaluation.
1814
[Page extract]
Comparisons with elastic modulus
The elastic modulus measures stiffness only within the initial linear elastic range, where deformation is fully recoverable.
1815
[Page extract]
Applications and benefits
Industrial applications
Tension and compression testing is used across multiple industries to validate design performance, assure quality, and meet regulatory requirements:
1816
[Page extract]
Speak to an expert
The Delft tear test is a valuable tool for assessing material performance in applications where durability and safety are critical.
1817
[Page extract]
What is 180 degree peel testing
The 180 degree peel test is a recognised method for measuring the strength of adhesive bonds when a material is peeled back on itself at a constant angle of 180 degrees.
1818
Test Frame
MultiTest test frame (twin column)
MultiTest test frame
A motorised test frame driven by twin ballscrews featuring dual-columns and designed to apply tension and compression from 2 N right up to a capacity of 50 kN (1100 lbf).Its versatile construction makes it perfectly suited for testing…
1819
[Page extract]
Methods of compressive burst testing
Inflationary burst testing
In this method, internal pressure is gradually increased using air, gas, or liquid until the container ruptures. This is widely applied to:
1820
Software
VectorPro Software (Zug u. Druck)
VectorPro® Software
VectorPro ist ein fortschrittliches Softwarepaket für Kraftprüfungen, das für die Durchführung von Zug-, Scher-, Biege- und Druckprüfungen an Materialien, Bauteilen und Produkten entwickelt wurde. Stellen Sie Messdaten grafisch dar und…
1821
Accessory
Montageplatte für Kraftmessdosen mit Schnellwechsel-Befestigung, Typ G, 25 mm Schlitz mit M16-Bolzen für 25 kN S-Form Kraftmessdose
432-288
Montageplatte QC Typ G inkl. M16-Bolzen
Mit 25 mm Schlitz. Lässt sich anhand des M16-Bolzen an die Kraftmessdose ILC-T 25 kN befestigen, damit ein Adapterzapfen QC Typ C (432-284) verwendet werden kann.
1822
Accessory
Blank (smooth) jaws for Lightweight Pneumatic Plane Grip, 200 N, 25 x 25 mm
Mec94-B25
Blank Jaws (10mm high x 25mm wide) - smooth steel jaw. Allows user to machine or affix own surface (eg. abrasive 'emery' paper).
Opening span = 0 - 20 mm.
Supplied as 0.5 set = 2 jaws (left…
1823
Accessory
QC Type G Loadcell Mounting Plate, 25 mm slot c/w M16 bolt for 25 kN S-beam loadcell
432-288
QC Type F Loadcell Mounting Plate c/w M16 bolt.
Fitted with 25 mm slot to suit 25kN S-beam loadcell. The M16 bolt is used to secure the mounting plate onto the loadcell so that a QC type C Male Post (432-284) can be affixed to the loadcell.
1824
Accessory
Blank (smooth) jaws for Mec154 Heavy-duty Vice Grip, 20kN, 40 x 60 mm
Mec154-B
Blank Jaws (40mm high x 60mm wide) - smooth steel jaw.
Opening span = 0 - 34 mm.
Allows user to machine or affix own surface (eg. abrasive 'emery' paper).
Supplied as 0.5 set = 2 jaws (left…
1825
Accessory
Montageplatte für Kraftmessdosen mit Schnellwechsel-Befestigung, Typ F, 25 mm Schlitz mit M12-Bolzen für 2.5, 5 und 10 kN S-Form Kraftmessdosen
432-287
Montageplatte QC Typ F inkl. M12-Bolzen
Mit 25 mm Schlitz. Lässt sich anhand des M12-Bolzen an die Kraftmessdosen ILC-S 2.5, 5 und ILC-T 10 kN befestigen, damit ein Adapterzapfen QC Typ C (432-284) verwendet werden kann.