Search results
751
Accessory
Diamond-coated Inset jaws, 0.5 set
Mec9-EBD
MEC9-EBD Diamond Jaws
Diamond-coated Inset jaws of 37 mm height x 15 mm width, 0.5 set. For fitting into the carrier of the MEC9 Thin Wire Grip.
Used when jaws need to bite into a soft material to clamp tightly and reduce the risk of slippage.(e.g. soft…
752
Accessory
Blank (smooth) Inset Jaws for MEC9 Thin Wire Grip, 2.5 kN
Mec9-EB
MEC9-EB Blank Jaws
Blank (smooth) inset jaws of 37 mm height x 15 mm width, 0.5 set. For fitting into the carrier of the MEC9 Thin Wire Grip.
Used when jaws require a specific surface to be machined onto them. Alternatively for affixing an abrasive…
753
Accessory
Float glass plates (10 pieces), 2" x 8" for FINAT 2 Peel Table
PSV15030
A set of 10 pieces of 2" wide x 8" long (51 x 203mm) float-glass plates. Used to mount adhesive specimens on when testing tensile peel strength to the requirements of FINAT and other standards.
For use with the FINAT 2 Assisted Peel Table - part number…
754
Accessory
Crush Test Fixture with Precision Guide
PSV21062
Precise alignment of the upper compression plate with the test piece is essential for optimum accuracy of results. Mecmesin recommends a minimum of self-adjusting compression plates and, for ECT and RCT tests, the Crush Test Fixture featuring a Precision…
755
Accessory
Lightweight Mini Vice Grip, 5 N, M6
432-281
By virtue of its spring loaded clamping action the Lightweight Mini Vice Grip is ideal for testing ultra low forces.
Weighing only 30 g it holds specimens without the need to tighten jaws by a thread, which may damage low-capacity loadcells or even the…
756
Accessory
Bench mounting stand for 'TS' Static Torque Screwdrivers
432-402
Bench mounting stand used for fixing the mid-torque range of 'TS' Static Torque Screwdrivers.
A clearance hole at each end allows the stand to be securely fixed to a bench.
Note: Not suitable for fixing the low-torque range of 'TTH' Mini Torque…
757
Accessory
Excel macro for calculating Z-value (M&S requirement)
840-215
A basic Excel macro which can present the data obtained during "test-to-failure" tests to check the security of attachments in the report-format requested by Marks & Spencer (M&S).
758
Accessory
3/8" Upper Chuck Assembly for use on Helixa sensors
432-615
A standard self-centering 3-jaw chuck with key.
It has a maximum ⅜" (9.5 mm) opening and is connected to the Helixa torque sensor via an adaptor with female ⅜" square hole.
Used to secure a variety of test specimens for torque applications of 1.5 - 10…
759
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-BG
Rubber-faced Jaws (30mm x 30mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
760
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 100 mm
Mec240k-BG100
Rubber-faced Jaws (30mm x 100mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact…
761
Accessory
Blank (smooth) Inset Jaws for MEC9 Thin Wire Grip, 2.5 kN
Mec9-EB
MEC9-EB Blank Jaws
Blank (smooth) inset jaws of 37 mm height x 15 mm width, 0.5 set. For fitting into the carrier of the MEC9 Thin Wire Grip.
Used when jaws require a specific surface to be machined onto them. Alternatively for affixing an abrasive…
762
Accessory
Mitutoyo DP-1VA Series 264-Digimatic Mini-Processor (US)
432-206
A palm-sized printer manufactured by Mitutoyo. It is used to print measurement data from the digimatic signal of digital force and torque instruments.
Performs statistical analysis and can draw a histogram or D chart in addition to more complicated…
763
Accessory
Transit Case for Manual Handling/Ergonomic Kit
416-007
A foam-lined rugged metal case for the components of the advanced or basic manual handling kit. Supplied as standard with the kit, has space for: a force gauge including rechargeable batteries, mains adaptor / battery charger, gripping cradle, chain link…
764
Accessory
QC Type C Adapter, 20 mm M, c/w pin and M6 fixing screws
432-284
QC Male Post 20mm c/w cross-pin, locking collar…
765
Accessory
Bench mounting stand for 'ST' range of mid- and high-range static torque transducers
432-401
Bench mounting stand supplied with all screws used for fixing the 'ST' range of mid- and high-range Static Torque Transducers.
Also equipped with an angled fixing bracket to mount the AFTI display at a convenient viewing angle.
A clearance hole at…
766
Accessory
Automated Syringe Batch Tester
PDV19179
The Automated Syringe Batch tester is a bench-top system for checking the ‘break-loose’ and ‘glide force’ of up to 12 individual syringes in one ‘load-and-run’ cycle. In the face of increased demand on production of syringes, this system enables larger…
767
Accessory
Rubber jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 60 x 200 mm
Mec83-BG200
Rubber-faced Jaws (60mm x 200mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
For fragile samples, which may get weakened by…
768
Accessory
Rubber jaws for Mec240k Medium Vice Grip, 2.5 kN, 30 x 30 mm
Mec240k-BG
Rubber-faced Jaws (30mm x 30mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
769
Accessory
Mitutoyo DP-1VA Series 264-Digimatic Mini-Processor (Euro)
432-205
A palm-sized printer manufactured by Mitutoyo. It is used to print measurement data from the digimatic signal of digital force and torque instruments.
Performs statistical analysis and can draw a histogram or D chart in addition to more complicated…
770
Accessory
Mini V-block, for Orbis & Tornado
432-423
The Mini V-block is a precision-engineered vice assembly which allows smaller specimens to be securely held in a centrally-aligned position, without excessive clamping force.
Supplied with V-shape, rubber-coated, interlocking jaws with an opening span…
771
Accessory
Peg Hook, 50 N, 10-32 UNF
432-399
The Peg Hook is fitted with 10-32 UNF female thread and supplied with a male grub-screw. It is designed for use in low-load applications where a small 'eyelet' needs to be held. The angled peg is ideal for quick and easy securing of the eyelet.
772
Accessory
FPT Tear Vice-Grips (pair), 100 mm rubber jaws, QC-8
432-625
A Lightweight Double-action Vice Grip providing free adjustment of both jaws, allowing them to be aligned around the central axis to accommodate tensile and tear testing of both symmetrical and asymmetrical specimens.
Fitted with 100mm-wide, rubber-…
773
Accessory
Rubber jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 100 mm
Mec83-BG100
Rubber-faced Jaws (40mm x 100mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
For fragile samples, which may get weakened by…
774
Accessory
Mitutoyo DP1-VA Series 264-Digimatic Mini-Processor (UK)
432-204
A palm-sized printer manufactured by Mitutoyo. It is used to print measurement data from the digimatic signal of digital force and torque instruments.
Performs statistical analysis and can draw a histogram or D chart in addition to more complicated…
775
Accessory
Button Pull-off Fixture, 500 N, 10-32 UNF
432-175
Used to test the security of buttons and other textile attachments. The slotted button pull fixture has interchangeable plates for different sizes of shank (3, 5 and 7 mm), and a shatter-protection guard.
Connects to loadcell and used with a motorised…