Search results
701
[Page extract]
Equipment and procedures
SCT testing equipment and tools
Accurate SCT testing requires equipment that can apply controlled and repeatable loads:
702
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
703
[Page extract]
How is bulk analysis testing performed?
Compression testing
Compression testing is used to assess how materials respond when compacted.
705
[Page extract]
Understanding corrugated cardboard resistance
The compressive resistance of corrugated cardboard depends on factors such as flute profile, board structure, and paper quality.
706
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
707
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?
708
[Page extract]
ASTM D3032
These test methods detail the standard procedures for testing hookup wire insulations including all components of the insulation system used on single insulated conductors or an assembly of single insulated conductors such as a cable bundle and harness
709
Event
Fundamentals of Food Texture Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
710
[Page extract]
ASTM F36-15
The ASTM F36 test method covers the determination of the short-time compressibility and recovery at room temperature of sheet-gasket materials, form-in-place gaskets, and in certain cases, gaskets cut from sheets.
711
Event
Top-load testing: Ensuring packaging integrity from production to transport
Top-load testing is the method used to simulate and measure the force exerted on packaging containers during production, filling, capping, storage, and transport.
712
[Page extract]
ISO 20795-1
ISO 20795-1:2013 classifies denture base polymers and copolymers and specifies their requirements. It also specifies the test methods to be used in determining compliance with these requirements.
713
[Page extract]
How is a three-point bend test performed?
Test setup and procedure
The test begins with preparing a specimen, often a rectangular bar, from materials such as plastics, composites, wood, or metals.
714
[Page extract]
What is the grab method?
The grab method is a tensile testing technique where only the centre of a fabric specimen is gripped during testing — typically using 100 mm × 150 mm test specimens with a 50 mm wide clamp
715
[Page extract]
Bend jigs
Flexural load tests are popular since they closely characterise how a material or component may perform during its lifetime.
716
Accessory
Coefficient of Friction COF Fixture (ISO 8295)
432-501
Designed to measure the coefficient of friction (COF) to ISO 8295 between two pieces of material. The COF test determines the kinetic and static resistance of one surface being dragged across another. This friction table can be precisely leveled.
717
Accessory
Toggle Clamps, 50 mm, serrated, 500 N, 10-32 UNF
432-176
Toggle Clamp (serrated)
An adjustable jaw can be positioned to ensure that symmetrical or asymmetrical specimens are aligned centrally. The other jaw is fitted to a toggle mechanism operated by a lever to allow rapid, easy clamping of specimens for…
718
Accessory
Rubber jaws for Mec83 U-Form Pneumatic Vice Grip, 5 kN, 40 x 60 mm
Mec83-BG
Rubber-faced Jaws (40mm x 60mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = 0-10mm, 10-20mm or 20-30mm depending on which rod and piston are fitted to the Mec83 body.
For fragile samples, which may get weakened by…
719
Accessory
Protective Dust Cover for fitting to MultiTest 2.5-xt stand (500 mm) and console
432-484
The covers offer protection to MultiTest 2.5-xt motorised test stands in dusty and dirty environments.
They are durable and easy to clean, and feature quick-acting velcro fastening strips for simple fitting and removal.
Dust covers are available for…
720
Accessory
Event-input cable for "switch-testing" on NEW(2011 - present) MultiTest/Vortex/Helixa-i and 'xt' stands
351-080
Event-Input Cable comprising 25-pin connector to split-connection fitted with a pair of 'crocodile clips'.
Allows a switch to be tested and the force/displacement/time to be identified when the switch closes or opens.
For use with the 'i' and 'xt'…
721
Accessory
Rubber jaws for Mec240g U-Form Vice Grip, 5 kN, 30 x 80 mm
Mec240g-BG80
Rubber-faced Jaws (30mm x 80mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
722
Accessory
Small Chain Link Assembly (short), 500 N, 10-32 UNF
432-259
The small Chain Link Assembly (short) is fitted with a 10-32 UNF female thread and supplied with a male grub-screw.
It is fixed to other grips thereby allowing a flexible connection, which is essential to avoid damaging light-capacity loadcells when…
723
Accessory
Rubber jaws for Mec240g U-Form Vice Grip, 5 kN, 30 x 80 mm
Mec240g-BG80
Rubber-faced Jaws (30mm x 80mm) - nickel-plated having 1mm thick layer of nitrile rubber coating.
Opening span = see datasheet for various spans according to the grip body selected.
For fragile samples, which may get weakened by pinching at the contact-…
724
Accessory
Float glass plates (10 pieces), 2" x 8" for FINAT 2 Peel Table
PSV15030
A set of 10 pieces of 2" wide x 8" long (51 x 203mm) float-glass plates. Used to mount adhesive specimens on when testing tensile peel strength to the requirements of FINAT and other standards.
For use with the FINAT 2 Assisted Peel Table - part number…
725
Accessory
Protective Dust Cover for fitting to MultiTest 2.5-i stand (500 mm)
432-483
The covers offer protection to MultiTest 2.5-i motorised test stands in dusty and dirty environments.
They are durable and easy to clean, and feature quick-acting velcro fastening strips for simple fitting and removal.
Dust covers are available for…