Search results
676
Event
Essentials of Cork Pull & Cork Elasticity Testing
Cork stoppers are extremely successful wine bottle closures that have been in use from ancient times.
677
[Page extract]
ISO 13935-1
ISO 13935-1:2014 specifies a procedure to determine the seam maximum force of sewn seams when the force is applied perpendicularly to the seam. ISO 13935-1:2014 specifies the method known as the strip test.
678
[Page extract]
Torque testing
Torque testing is a way of determining how an object will react when it is being turned - during normal operation or being twisted until it deliberately fails or breaks.
679
Event
Fundamentals of Food Texture Testing and Analysis
Texture cannot be controlled unless it measured in a consistent and repeatable manner.
680
[Page extract]
BS EN ISO 9000
ISO 9000 gives an overview of the fundamentals and concepts around quality management.
682
Event
Cork Pull & Cork Compression Testing OnDemand Webinar
FORCE TESTING in Wine & Spirit Applications
683
[Page extract]
Introduction to the ring crush test
The ring crush test (RCT) is a key method for determining the edgewise compression strength of paper and paperboard.
684
[Page extract]
Introduction to climbing drum peel testing
Climbing drum peel testing is a specialised method used to measure the adhesive strength between bonded materials, particularly in flexible-to-rigid substrate combinations such as aluminium skins bonded to honeycomb cores.
685
[Page extract]
ISO 1827
ISO 1827 specifies methods for the determination of the modulus in shear and the strength of bonds of rubber to metal or other rigid plates, using rubber bonded between four parallel plates.
686
[Page extract]
BS EN ISO 71-2
BS EN 71-2 covers the flammable materials which are prohibited in all toys and the requirements concerning flammability of certain toys when exposed to fire.
687
Event
Webinar: Adhesion/Peel strength testing
There is a reason people reach for duct tape as a fix for almost everything – adhesion strength.
From busted pipes to ripped furniture, the preference for a solution that “does not easily peel off” is the guiding principle for manufacturers.
688
[Page extract]
Introduction to short span compression tests
The short span compression test (SCT) is a mechanical testing method used to measure the compressive strength of materials over a very short span.
689
[Page extract]
Procedure for tensile testing
While the specifics vary depending on material type and applicable standards, the general procedure includes:
690
[Page extract]
ASTM D5635-11
An important factor affecting the performance of membrane roofing systems is their ability to resist dynamic puncture loads. This test method provides a means to assess dynamic puncture resistance.
691
Event
Fundamentals of Texture Testing Analysis
The primary goal for using instrumentation to measure texture is to capture an objective value to something that is typically evaluated very subjectively. Texture cannot be controlled unless it measured in a consistent and repeatable manner.
692
[Page extract]
Comparing FCT with CMT
The flat crush test measures the compressive strength of the fluted structure in finished board, taking into account liners and adhesives.
693
[Page extract]
Introduction to single lap shear testing
Single lap shear testing is a widely used method for determining the shear strength of an adhesive bond between two overlapping materials.
694
[Page extract]
What is ultimate compressive strength?
Ultimate compressive strength is the maximum compressive stress a material can sustain before failure.
695
[Page extract]
ASTM F2606-08
This guide can be used to obtain force versus deflection or midspan bending moment versus midspan curvature curves for stents and stent systems subjected to three-point bending conditions.
696
[Page extract]
What is double lap shear testing?
Double lap shear testing is a mechanical method used to measure the shear strength of adhesive bonds.
697
[Page extract]
ASTM D4179
1.1 This test method covers determining the resistance of formed catalysts and catalyst carriers to compressive force and is applicable to regular catalyst shapes such as tablets and spheres.
698
[Page extract]
Performing a five-point bend test
Specimen preparation
Cut specimens to the standardised dimensions specified in ASTM D2718.
Ensure surfaces are smooth and free from defects that could affect results.<
699
[Page extract]
Applicators and dispensers
Applicators and dispensers are designed to provide uniform coverage of semi-solids, liquids and viscous matter such as creams and lotions. They are often integrated with the product's packaging so that the packaging also acts as a dispenser.
700
Event
Fundamentals of Compression Testing
How much force is required to register a command when you click your computer mouse?
How much force can a water bottle take before it collapses in its case under a stack?