Search results
1826
[Page extract]
ASTM D6175-03
5.1 This test method is intended to provide information on the ability of an extruded catalyst to retain physical integrity during use.
1827
[Page extract]
Plates
Compression fixtures should be selected to suit the contact area of the sample which is to be tested.
1828
[Page extract]
Digital torque testers
Great value, easy to use handheld torque instruments that are ideal for product testing in quality control (QC) labs and on the production line.
1829
[Page extract]
ASTM E328-02
These test methods cover the determination of the time dependence of stress (stress relaxation) in materials and structures under conditions of approximately constant constraint, constant environment, and negligible vibration.
1830
[Page extract]
ASTM D3914
ASTM D3914 is a test method used to measure the in-plane shear strength of pultruded, glass-fiber reinforced, thermosetting plastic rod in diameters ranging from 19 to 32 mm.
1831
Event
Fundamentals of Compression Testing
Push or compressive testing helps determine the limits of most products that require constant pushing or compression.
1832
[Page extract]
ASTM D6742 / D6742M
ASTM D6742 is the standard test method for tensile and compression testing of filled-hole polymer matrix composite laminates. It provides instructions for modifying open-hole tension and compression test methods to determine filled-hole tensile and com
1833
Case study
Spielzeugprüfung nach Sicherheitsstandards für die Befestigungsstärke
Anforderung
Der Kunde liefert Plüschgeschenke an Einzelhändler wie Clintons.
1834
[Page extract]
BS ISO 7743
ISO 7743 specifies methods for the determination of the compression stress-strain properties of vulcanized or thermoplastic rubber using a standard test piece, a product or a part of a product.
Four procedures are given:
1835
[Page extract]
ISO 11897
ISO 11897 specifies a method for the determination, under given conditions, of the resistance to tear propagation on an edge fold of sacks made from thermoplastic flexible film.
1836
[Page extract]
ISO 1926
ISO 1926 specifies a method of determining the behaviour of rigid cellular plastics materials when they are subjected to a tensile stress.
1837
Case study
Manipulationssicherer Ringtest
Anforderung Der Kunde fertigt Verschlüsse für die Getränkeindustrie. Dazu gehören Originalitätskappen für Mineralwässer und andere alkoholfreie Getränke.
1838
[Page extract]
IEC 62137-1-1
The test method described in IEC 62137-1-1:2007 is applicable to gull-wing lead surface mounting components.
1839
Case study
Test der Sicherheitsgurtverriegelung
Anforderung Der Kunde verlangte ein System zur Messung der Kraft, die erforderlich ist, um den Verriegelungsmechanismus eines unter Spannung stehenden Autosicherheitsgurts zu lösen.
1840
[Page extract]
ASTM D790-17
ASTM D790 is used to determine the flexural properties of unreinforced and reinforced plastics, including high modulus composites and electrical insulating materials utilizing a three-point loading system to apply a load to a simply supported beam (spec
1841
[Page extract]
ISO 10354
Simulates in a qualitative manner the forces and effects on an adhesive-bonded joint at a metal-adhesive/primer interface. It can also be used as a method of checking the surface preparation of substrates.
1842
Sensor
Sensors - Helixa
Torque sensors
The HTC range of interchangeable torque sensors are specially adapted for the Helixa test system. Plug and play for automatic calibration with availability to suit all requirements in capacities from 0.1 N.m (0.9 lbf.in) to 6 N.m (50 lbf.in…
1843
[Page extract]
ISO 7886-2
This document specifies requirements for sterile single-use hypodermic syringes of nominal capacity 1 ml and above, made of plastic materials and intended for use with power-driven syringe pumps. Annexe B covers the Pump Force to be measured.
1844
[Page extract]
ASTM D1321
This test method covers the empirical estimation of the consistency of waxes derived from petroleum by measurement of the extent of penetration of a standard needle.
1845
[Page extract]
ISO 8033
ISO 8033 specifies methods for the determination of the adhesion between lining and reinforcement, between cover and reinforcement, between reinforcement layers, between cover and outer lamination (thin layer of material outside the cover for protection
1846
Case study
Messung der Federkennlinien der Kraftstoffpumpe
Anforderung Einer der größten Automobilteilehersteller in der Tschechischen Republik, der zu einer großen Gruppe gehört, verlangte eine Reihe von Bauteilen, die unter hohen Belastungen getestet wurden.
1847
[Page extract]
ISO 20502
SO 20502:2005 describes a method of testing ceramic coatings by scratching with a diamond stylus.
1848
Case study
Identitätskarten abziehen
Anforderung Der Kunde stellt Ausweise mit laminiertem Umschlag her.
1849
[Page extract]
Torque systems
Do you need a level of accuracy and repeatability which just cannot be achieved by manual testers? Do you want to reduce testing time and increase throughput for operators when performing batch tests?
1850
Case study
Drehmomentprüfgerät für eine Reihe von Originalitätskappen
Anforderung Elopak benötigte Ausrüstung für die manuelle Prüfung von manipulationssicheren Verschlüssen an Flaschenverschlüssen, ohne dass die Flasche vorhanden war.